Viewing file:  uninorth.h (4.73 KB) -rw-r--r--
Select action/file-type:
 (+) |  (+) |  (+) | Code (+) | Session (+) |  (+) | SDB (+) |  (+) |  (+) |  (+) |  (+) |  (+) |
/*
* BK Id: SCCS/s.uninorth.h 1.13 10/23/01 08:09:35 trini
*/
/*
* uninorth.h: definitions for using the "UniNorth" host bridge chip
* from Apple. This chip is used on "Core99" machines
*
*/
#ifdef __KERNEL__
#ifndef __ASM_UNINORTH_H__
#define __ASM_UNINORTH_H__
/*
* Uni-N config space reg. definitions
*
* (Little endian)
*/
/* Address ranges selection. This one should work with Bandit too */
#define UNI_N_ADDR_SELECT 0x48
#define UNI_N_ADDR_COARSE_MASK 0xffff0000 /* 256Mb regions at *0000000 */
#define UNI_N_ADDR_FINE_MASK 0x0000ffff /* 16Mb regions at f*000000 */
/* AGP registers */
#define UNI_N_CFG_GART_BASE 0x8c
#define UNI_N_CFG_AGP_BASE 0x90
#define UNI_N_CFG_GART_CTRL 0x94
#define UNI_N_CFG_INTERNAL_STATUS 0x98
/* UNI_N_CFG_GART_CTRL bits definitions */
#define UNI_N_CFG_GART_INVAL 0x00000001
#define UNI_N_CFG_GART_ENABLE 0x00000100
#define UNI_N_CFG_GART_2xRESET 0x00010000
/* My understanding of UniNorth AGP as of UniNorth rev 1.0x,
* revision 1.5 (x4 AGP) may need further changes.
*
* AGP_BASE register contains the base address of the AGP aperture on
* the AGP bus. It doesn't seem to be visible to the CPU as of UniNorth 1.x,
* even if decoding of this address range is enabled in the address select
* register. Apparently, the only supported bases are 256Mb multiples
* (high 4 bits of that register).
*
* GART_BASE register appear to contain the physical address of the GART
* in system memory in the high address bits (page aligned), and the
* GART size in the low order bits (number of GART pages)
*
* The GART format itself is one 32bits word per physical memory page.
* This word contains, in little-endian format (!!!), the physical address
* of the page in the high bits, and what appears to be an "enable" bit
* in the LSB bit (0) that must be set to 1 when the entry is valid.
*
* Obviously, the GART is not cache coherent and so any change to it
* must be flushed to memory (or maybe just make the GART space non
* cachable). AGP memory itself doens't seem to be cache coherent neither.
*
* In order to invalidate the GART (which is probably necessary to inval
* the bridge internal TLBs), the following sequence has to be written,
* in order, to the GART_CTRL register:
*
* UNI_N_CFG_GART_ENABLE | UNI_N_CFG_GART_INVAL
* UNI_N_CFG_GART_ENABLE
* UNI_N_CFG_GART_ENABLE | UNI_N_CFG_GART_2xRESET
* UNI_N_CFG_GART_ENABLE
*
* As far as AGP "features" are concerned, it looks like fast write may
* not be supported but this has to be confirmed.
*
* Turning on AGP seem to require a double invalidate operation, one before
* setting the AGP command register, on after.
*
* Turning off AGP seems to require the following sequence: first wait
* for the AGP to be idle by reading the internal status register, then
* write in that order to the GART_CTRL register:
*
* UNI_N_CFG_GART_ENABLE | UNI_N_CFG_GART_INVAL
* 0
* UNI_N_CFG_GART_2xRESET
* 0
*/
/*
* Uni-N memory mapped reg. definitions
*
* Those registers are Big-Endian !!
*
* Their meaning come from either Darwin and/or from experiments I made with
* the bootrom, I'm not sure about their exact meaning yet
*
*/
/* Version of the UniNorth chip */
#define UNI_N_VERSION 0x0000 /* Known versions: 3,7 and 8 */
/* This register is used to enable/disable various clocks */
#define UNI_N_CLOCK_CNTL 0x0020
#define UNI_N_CLOCK_CNTL_PCI 0x00000001 /* PCI2 clock control */
#define UNI_N_CLOCK_CNTL_GMAC 0x00000002 /* GMAC clock control */
#define UNI_N_CLOCK_CNTL_FW 0x00000004 /* FireWire clock control */
/* Power Management control */
#define UNI_N_POWER_MGT 0x0030
#define UNI_N_POWER_MGT_NORMAL 0x00
#define UNI_N_POWER_MGT_IDLE2 0x01
#define UNI_N_POWER_MGT_SLEEP 0x02
/* This register is configured by Darwin depending on the UniN
* revision
*/
#define UNI_N_ARB_CTRL 0x0040
#define UNI_N_ARB_CTRL_QACK_DELAY_SHIFT 15
#define UNI_N_ARB_CTRL_QACK_DELAY_MASK 0x0e1f8000
#define UNI_N_ARB_CTRL_QACK_DELAY 0x30
#define UNI_N_ARB_CTRL_QACK_DELAY105 0x00
/* This one _might_ return the CPU number of the CPU reading it;
* the bootROM decides wether to boot or to sleep/spinloop depending
* on this register beeing 0 or not
*/
#define UNI_N_CPU_NUMBER 0x0050
/* This register appear to be read by the bootROM to decide what
* to do on a non-recoverable reset (powerup or wakeup)
*/
#define UNI_N_HWINIT_STATE 0x0070
#define UNI_N_HWINIT_STATE_SLEEPING 0x01
#define UNI_N_HWINIT_STATE_RUNNING 0x02
/* This last bit appear to be used by the bootROM to know the second
* CPU has started and will enter it's sleep loop with IP=0
*/
#define UNI_N_HWINIT_STATE_CPU1_FLAG 0x10000000
/* Uninorth 1.5 rev. has additional perf. monitor registers at 0xf00-0xf50 */
#endif /* __ASM_UNINORTH_H__ */
#endif /* __KERNEL__ */
|