Viewing file:  t128.h (4.78 KB) -rw-r--r--
Select action/file-type:
 (+) |  (+) |  (+) | Code (+) | Session (+) |  (+) | SDB (+) |  (+) |  (+) |  (+) |  (+) |  (+) |
/*
* Trantor T128/T128F/T228 defines
* Note : architecturally, the T100 and T128 are different and won't work
*
* Copyright 1993, Drew Eckhardt
* Visionary Computing
* (Unix and Linux consulting and custom programming)
* drew@colorado.edu
* +1 (303) 440-4894
*
* DISTRIBUTION RELEASE 3.
*
* For more information, please consult
*
* Trantor Systems, Ltd.
* T128/T128F/T228 SCSI Host Adapter
* Hardware Specifications
*
* Trantor Systems, Ltd.
* 5415 Randall Place
* Fremont, CA 94538
* 1+ (415) 770-1400, FAX 1+ (415) 770-9910
*
* and
*
* NCR 5380 Family
* SCSI Protocol Controller
* Databook
*
* NCR Microelectronics
* 1635 Aeroplaza Drive
* Colorado Springs, CO 80916
* 1+ (719) 578-3400
* 1+ (800) 334-5454
*/
/*
* $Log: t128.h,v $
*/
#ifndef T128_H
#define T128_H
#define T128_PUBLIC_RELEASE 3
#define TDEBUG_INIT 0x1
#define TDEBUG_TRANSFER 0x2
/*
* The trantor boards are memory mapped. They use an NCR5380 or
* equivalent (my sample board had part second sourced from ZILOG).
* NCR's recommended "Pseudo-DMA" architecture is used, where
* a PAL drives the DMA signals on the 5380 allowing fast, blind
* transfers with proper handshaking.
*/
/*
* Note : a boot switch is provided for the purpose of informing the
* firmware to boot or not boot from attached SCSI devices. So, I imagine
* there are fewer people who've yanked the ROM like they do on the Seagate
* to make bootup faster, and I'll probably use this for autodetection.
*/
#define T_ROM_OFFSET 0
/*
* Note : my sample board *WAS NOT* populated with the SRAM, so this
* can't be used for autodetection without a ROM present.
*/
#define T_RAM_OFFSET 0x1800
/*
* All of the registers are allocated 32 bytes of address space, except
* for the data register (read/write to/from the 5380 in pseudo-DMA mode)
*/
#define T_CONTROL_REG_OFFSET 0x1c00 /* rw */
#define T_CR_INT 0x10 /* Enable interrupts */
#define T_CR_CT 0x02 /* Reset watchdog timer */
#define T_STATUS_REG_OFFSET 0x1c20 /* ro */
#define T_ST_BOOT 0x80 /* Boot switch */
#define T_ST_S3 0x40 /* User settable switches, */
#define T_ST_S2 0x20 /* read 0 when switch is on, 1 off */
#define T_ST_S1 0x10
#define T_ST_PS2 0x08 /* Set for Microchannel 228 */
#define T_ST_RDY 0x04 /* 5380 DRQ */
#define T_ST_TIM 0x02 /* indicates 40us watchdog timer fired */
#define T_ST_ZERO 0x01 /* Always zero */
#define T_5380_OFFSET 0x1d00 /* 8 registers here, see NCR5380.h */
#define T_DATA_REG_OFFSET 0x1e00 /* rw 512 bytes long */
#ifndef ASM
int t128_abort(Scsi_Cmnd *);
int t128_biosparam(Disk *, kdev_t, int*);
int t128_detect(Scsi_Host_Template *);
int t128_queue_command(Scsi_Cmnd *, void (*done)(Scsi_Cmnd *));
int t128_reset(Scsi_Cmnd *, unsigned int reset_flags);
int t128_proc_info (char *buffer, char **start, off_t offset,
int length, int hostno, int inout);
#ifndef NULL
#define NULL 0
#endif
#ifndef CMD_PER_LUN
#define CMD_PER_LUN 2
#endif
#ifndef CAN_QUEUE
#define CAN_QUEUE 32
#endif
/*
* I hadn't thought of this with the earlier drivers - but to prevent
* macro definition conflicts, we shouldn't define all of the internal
* macros when this is being used solely for the host stub.
*/
#define TRANTOR_T128 { \
name: "Trantor T128/T128F/T228", \
detect: t128_detect, \
queuecommand: t128_queue_command, \
abort: t128_abort, \
reset: t128_reset, \
bios_param: t128_biosparam, \
can_queue: CAN_QUEUE, \
this_id: 7, \
sg_tablesize: SG_ALL, \
cmd_per_lun: CMD_PER_LUN, \
use_clustering: DISABLE_CLUSTERING}
#ifndef HOSTS_C
#define NCR5380_implementation_fields \
unsigned long base
#define NCR5380_local_declare() \
unsigned long base
#define NCR5380_setup(instance) \
base = (instance)->base
#define T128_address(reg) (base + T_5380_OFFSET + ((reg) * 0x20))
#if !(TDEBUG & TDEBUG_TRANSFER)
#define NCR5380_read(reg) isa_readb(T128_address(reg))
#define NCR5380_write(reg, value) isa_writeb((value),(T128_address(reg)))
#else
#define NCR5380_read(reg) \
(((unsigned char) printk("scsi%d : read register %d at address %08x\n"\
, instance->hostno, (reg), T128_address(reg))), isa_readb(T128_address(reg)))
#define NCR5380_write(reg, value) { \
printk("scsi%d : write %02x to register %d at address %08x\n", \
instance->hostno, (value), (reg), T128_address(reg)); \
isa_writeb((value), (T128_address(reg))); \
}
#endif
#define NCR5380_intr t128_intr
#define do_NCR5380_intr do_t128_intr
#define NCR5380_queue_command t128_queue_command
#define NCR5380_abort t128_abort
#define NCR5380_reset t128_reset
#define NCR5380_proc_info t128_proc_info
/* 15 14 12 10 7 5 3
1101 0100 1010 1000 */
#define T128_IRQS 0xc4a8
#endif /* else def HOSTS_C */
#endif /* ndef ASM */
#endif /* T128_H */
|