Viewing file:  sun3_scsi.c (13.38 KB) -rw-r--r--
Select action/file-type:
 (+) |  (+) |  (+) | Code (+) | Session (+) |  (+) | SDB (+) |  (+) |  (+) |  (+) |  (+) |  (+) |
/*
* Sun3 SCSI stuff by Erik Verbruggen (erik@bigmama.xtdnet.nl)
*
* Sun3 DMA routines added by Sam Creasey (sammy@oh.verio.com)
*
* Adapted from mac_scsinew.c:
*/
/*
* Generic Macintosh NCR5380 driver
*
* Copyright 1998, Michael Schmitz <mschmitz@lbl.gov>
*
* derived in part from:
*/
/*
* Generic Generic NCR5380 driver
*
* Copyright 1995, Russell King
*
* ALPHA RELEASE 1.
*
* For more information, please consult
*
* NCR 5380 Family
* SCSI Protocol Controller
* Databook
*
* NCR Microelectronics
* 1635 Aeroplaza Drive
* Colorado Springs, CO 80916
* 1+ (719) 578-3400
* 1+ (800) 334-5454
*/
/*
* This is from mac_scsi.h, but hey, maybe this is useful for Sun3 too! :)
*
* Options :
*
* PARITY - enable parity checking. Not supported.
*
* SCSI2 - enable support for SCSI-II tagged queueing. Untested.
*
* USLEEP - enable support for devices that don't disconnect. Untested.
*/
/*
* $Log: sun3_NCR5380.c,v $
*/
#define AUTOSENSE
#include <linux/types.h>
#include <linux/stddef.h>
#include <linux/ctype.h>
#include <linux/delay.h>
#include <linux/module.h>
#include <linux/signal.h>
#include <linux/sched.h>
#include <linux/ioport.h>
#include <linux/init.h>
#include <linux/blk.h>
#include <asm/io.h>
#include <asm/system.h>
#include <asm/sun3ints.h>
#include <asm/dvma.h>
#include <asm/idprom.h>
#include <asm/machines.h>
/* dma on! */
#define REAL_DMA
#include "scsi.h"
#include "hosts.h"
#include "sun3_scsi.h"
#include "NCR5380.h"
#include "constants.h"
#define USE_WRAPPER
#define RESET_BOOT
#define DRIVER_SETUP
#define NDEBUG 0
/*
* BUG can be used to trigger a strange code-size related hang on 2.1 kernels
*/
#ifdef BUG
#undef RESET_BOOT
#undef DRIVER_SETUP
#endif
#undef SUPPORT_TAGS
#define ENABLE_IRQ() enable_irq( IRQ_SUN3_SCSI );
static void scsi_sun3_intr(int irq, void *dummy, struct pt_regs *fp);
static inline unsigned char sun3scsi_read(int reg);
static inline void sun3scsi_write(int reg, int value);
static int setup_can_queue = -1;
static int setup_cmd_per_lun = -1;
static int setup_sg_tablesize = -1;
#ifdef SUPPORT_TAGS
static int setup_use_tagged_queuing = -1;
#endif
static int setup_hostid = -1;
static Scsi_Cmnd *sun3_dma_setup_done = NULL;
#define AFTER_RESET_DELAY (HZ/2)
/* ms to wait after hitting dma regs */
#define SUN3_DMA_DELAY 10
/* dvma buffer to allocate -- 32k should hopefully be more than sufficient */
#define SUN3_DVMA_BUFSIZE 0xe000
/* minimum number of bytes to do dma on */
#define SUN3_DMA_MINSIZE 128
static volatile unsigned char *sun3_scsi_regp;
static volatile struct sun3_dma_regs *dregs;
static unsigned char *dmabuf = NULL; /* dma memory buffer */
static struct sun3_udc_regs *udc_regs = NULL;
static unsigned char *sun3_dma_orig_addr = NULL;
static unsigned long sun3_dma_orig_count = 0;
static int sun3_dma_active = 0;
static unsigned long last_residual = 0;
/*
* NCR 5380 register access functions
*/
static inline unsigned char sun3scsi_read(int reg)
{
return( sun3_scsi_regp[reg] );
}
static inline void sun3scsi_write(int reg, int value)
{
sun3_scsi_regp[reg] = value;
}
/* dma controller register access functions */
static inline unsigned short sun3_udc_read(unsigned char reg)
{
unsigned short ret;
dregs->udc_addr = UDC_CSR;
udelay(SUN3_DMA_DELAY);
ret = dregs->udc_data;
udelay(SUN3_DMA_DELAY);
return ret;
}
static inline void sun3_udc_write(unsigned short val, unsigned char reg)
{
dregs->udc_addr = reg;
udelay(SUN3_DMA_DELAY);
dregs->udc_data = val;
udelay(SUN3_DMA_DELAY);
}
/*
* XXX: status debug
*/
static struct Scsi_Host *default_instance;
/*
* Function : int sun3scsi_detect(Scsi_Host_Template * tpnt)
*
* Purpose : initializes mac NCR5380 driver based on the
* command line / compile time port and irq definitions.
*
* Inputs : tpnt - template for this SCSI adapter.
*
* Returns : 1 if a host adapter was found, 0 if not.
*
*/
int sun3scsi_detect(Scsi_Host_Template * tpnt)
{
unsigned long ioaddr, iopte;
int count = 0;
static int called = 0;
struct Scsi_Host *instance;
/* check that this machine has an onboard 5380 */
switch(idprom->id_machtype) {
case SM_SUN3|SM_3_50:
case SM_SUN3|SM_3_60:
break;
default:
return 0;
}
if(called)
return 0;
tpnt->proc_name = "Sun3 5380 SCSI";
/* setup variables */
tpnt->can_queue =
(setup_can_queue > 0) ? setup_can_queue : CAN_QUEUE;
tpnt->cmd_per_lun =
(setup_cmd_per_lun > 0) ? setup_cmd_per_lun : CMD_PER_LUN;
tpnt->sg_tablesize =
(setup_sg_tablesize >= 0) ? setup_sg_tablesize : SG_TABLESIZE;
if (setup_hostid >= 0)
tpnt->this_id = setup_hostid;
else {
/* use 7 as default */
tpnt->this_id = 7;
}
/* Taken from Sammy's lance driver: */
/* IOBASE_SUN3_SCSI can be found within the IO pmeg with some effort */
for(ioaddr = 0xfe00000; ioaddr < (0xfe00000 + SUN3_PMEG_SIZE);
ioaddr += SUN3_PTE_SIZE) {
iopte = sun3_get_pte(ioaddr);
if(!(iopte & SUN3_PAGE_TYPE_IO)) /* this an io page? */
continue;
if(((iopte & SUN3_PAGE_PGNUM_MASK) << PAGE_SHIFT) ==
IOBASE_SUN3_SCSI) {
count = 1;
break;
}
}
if(!count) {
printk("No Sun3 NCR5380 found!\n");
return 0;
}
sun3_scsi_regp = (unsigned char *)ioaddr;
dregs = (struct sun3_dma_regs *)(((unsigned char *)ioaddr) + 8);
if((udc_regs = dvma_malloc(sizeof(struct sun3_udc_regs)))
== NULL) {
printk("SUN3 Scsi couldn't allocate DVMA memory!\n");
return 0;
}
#ifdef OLDDMA
if((dmabuf = dvma_malloc_align(SUN3_DVMA_BUFSIZE, 0x10000)) == NULL) {
printk("SUN3 Scsi couldn't allocate DVMA memory!\n");
return 0;
}
#endif
#ifdef SUPPORT_TAGS
if (setup_use_tagged_queuing < 0)
setup_use_tagged_queuing = DEFAULT_USE_TAGGED_QUEUING;
#endif
instance = scsi_register (tpnt, sizeof(struct NCR5380_hostdata));
if(instance == NULL)
return 0;
default_instance = instance;
instance->io_port = (unsigned long) ioaddr;
instance->irq = IRQ_SUN3_SCSI;
NCR5380_init(instance, 0);
instance->n_io_port = 32;
((struct NCR5380_hostdata *)instance->hostdata)->ctrl = 0;
if (request_irq(instance->irq, scsi_sun3_intr,
0, "Sun3SCSI-5380", NULL)) {
#ifndef REAL_DMA
printk("scsi%d: IRQ%d not free, interrupts disabled\n",
instance->host_no, instance->irq);
instance->irq = IRQ_NONE;
#else
printk("scsi%d: IRQ%d not free, bailing out\n",
instance->host_no, instance->irq);
return 0;
#endif
}
printk("scsi%d: Sun3 5380 at port %lX irq", instance->host_no, instance->io_port);
if (instance->irq == IRQ_NONE)
printk ("s disabled");
else
printk (" %d", instance->irq);
printk(" options CAN_QUEUE=%d CMD_PER_LUN=%d release=%d",
instance->can_queue, instance->cmd_per_lun,
SUN3SCSI_PUBLIC_RELEASE);
printk("\nscsi%d:", instance->host_no);
NCR5380_print_options(instance);
printk("\n");
dregs->csr = 0;
udelay(SUN3_DMA_DELAY);
dregs->csr = CSR_SCSI | CSR_FIFO | CSR_INTR;
udelay(SUN3_DMA_DELAY);
dregs->fifo_count = 0;
called = 1;
return 1;
}
int sun3scsi_release (struct Scsi_Host *shpnt)
{
if (shpnt->irq != IRQ_NONE)
free_irq (shpnt->irq, NULL);
return 0;
}
#ifdef RESET_BOOT
/*
* Our 'bus reset on boot' function
*/
static void sun3_scsi_reset_boot(struct Scsi_Host *instance)
{
unsigned long end;
NCR5380_local_declare();
NCR5380_setup(instance);
/*
* Do a SCSI reset to clean up the bus during initialization. No
* messing with the queues, interrupts, or locks necessary here.
*/
printk( "Sun3 SCSI: resetting the SCSI bus..." );
/* switch off SCSI IRQ - catch an interrupt without IRQ bit set else */
sun3_disable_irq( IRQ_SUN3_SCSI );
/* get in phase */
NCR5380_write( TARGET_COMMAND_REG,
PHASE_SR_TO_TCR( NCR5380_read(STATUS_REG) ));
/* assert RST */
NCR5380_write( INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_RST );
/* The min. reset hold time is 25us, so 40us should be enough */
udelay( 50 );
/* reset RST and interrupt */
NCR5380_write( INITIATOR_COMMAND_REG, ICR_BASE );
NCR5380_read( RESET_PARITY_INTERRUPT_REG );
for( end = jiffies + AFTER_RESET_DELAY; time_before(jiffies, end); )
barrier();
/* switch on SCSI IRQ again */
sun3_enable_irq( IRQ_SUN3_SCSI );
printk( " done\n" );
}
#endif
const char * sun3scsi_info (struct Scsi_Host *spnt) {
return "";
}
// safe bits for the CSR
#define CSR_GOOD 0x060f
static void scsi_sun3_intr(int irq, void *dummy, struct pt_regs *fp)
{
unsigned short csr = dregs->csr;
if(csr & ~CSR_GOOD) {
if(csr & CSR_DMA_BUSERR) {
printk("scsi%d: bus error in dma\n", default_instance->host_no);
}
if(csr & CSR_DMA_CONFLICT) {
printk("scsi%d: dma conflict\n", default_instance->host_no);
}
}
if(csr & (CSR_SDB_INT | CSR_DMA_INT))
NCR5380_intr(irq, dummy, fp);
}
/*
* Debug stuff - to be called on NMI, or sysrq key. Use at your own risk;
* reentering NCR5380_print_status seems to have ugly side effects
*/
/* this doesn't seem to get used at all -- sam */
#if 0
void sun3_sun3_debug (void)
{
unsigned long flags;
NCR5380_local_declare();
if (default_instance) {
save_flags(flags);
cli();
NCR5380_print_status(default_instance);
restore_flags(flags);
}
}
#endif
/* sun3scsi_dma_setup() -- initialize the dma controller for a read/write */
static unsigned long sun3scsi_dma_setup(void *data, unsigned long count, int write_flag)
{
#ifdef OLDDMA
if(write_flag)
memcpy(dmabuf, data, count);
else {
sun3_dma_orig_addr = data;
sun3_dma_orig_count = count;
}
#else
void *addr;
// addr = sun3_dvma_page((unsigned long)data, (unsigned long)dmabuf);
addr = (void *)dvma_map((unsigned long) data, count);
sun3_dma_orig_addr = addr;
sun3_dma_orig_count = count;
#endif
dregs->fifo_count = 0;
sun3_udc_write(UDC_RESET, UDC_CSR);
/* reset fifo */
dregs->csr &= ~CSR_FIFO;
dregs->csr |= CSR_FIFO;
/* set direction */
if(write_flag)
dregs->csr |= CSR_SEND;
else
dregs->csr &= ~CSR_SEND;
/* byte count for fifo */
dregs->fifo_count = count;
sun3_udc_write(UDC_RESET, UDC_CSR);
/* reset fifo */
dregs->csr &= ~CSR_FIFO;
dregs->csr |= CSR_FIFO;
if(dregs->fifo_count != count) {
printk("scsi%d: fifo_mismatch %04x not %04x\n",
default_instance->host_no, dregs->fifo_count,
(unsigned int) count);
NCR5380_print(default_instance);
}
/* setup udc */
#ifdef OLDDMA
udc_regs->addr_hi = ((dvma_vtob(dmabuf) & 0xff0000) >> 8);
udc_regs->addr_lo = (dvma_vtob(dmabuf) & 0xffff);
#else
udc_regs->addr_hi = (((unsigned long)(addr) & 0xff0000) >> 8);
udc_regs->addr_lo = ((unsigned long)(addr) & 0xffff);
#endif
udc_regs->count = count/2; /* count in words */
udc_regs->mode_hi = UDC_MODE_HIWORD;
if(write_flag) {
if(count & 1)
udc_regs->count++;
udc_regs->mode_lo = UDC_MODE_LSEND;
udc_regs->rsel = UDC_RSEL_SEND;
} else {
udc_regs->mode_lo = UDC_MODE_LRECV;
udc_regs->rsel = UDC_RSEL_RECV;
}
/* announce location of regs block */
sun3_udc_write(((dvma_vtob(udc_regs) & 0xff0000) >> 8),
UDC_CHN_HI);
sun3_udc_write((dvma_vtob(udc_regs) & 0xffff), UDC_CHN_LO);
/* set dma master on */
sun3_udc_write(0xd, UDC_MODE);
/* interrupt enable */
sun3_udc_write(UDC_INT_ENABLE, UDC_CSR);
return count;
}
static inline unsigned long sun3scsi_dma_count(struct Scsi_Host *instance)
{
unsigned short resid;
dregs->udc_addr = 0x32;
udelay(SUN3_DMA_DELAY);
resid = dregs->udc_data;
udelay(SUN3_DMA_DELAY);
resid *= 2;
return (unsigned long) resid;
}
static inline unsigned long sun3scsi_dma_residual(struct Scsi_Host *instance)
{
return last_residual;
}
static inline unsigned long sun3scsi_dma_xfer_len(unsigned long wanted, Scsi_Cmnd *cmd,
int write_flag)
{
if((cmd->request.cmd == 0) || (cmd->request.cmd == 1))
return wanted;
else
return 0;
}
/* clean up after our dma is done */
static int sun3scsi_dma_finish(int write_flag)
{
unsigned short count;
unsigned short fifo;
int ret = 0;
sun3_dma_active = 0;
// check to empty the fifo on a read
if(!write_flag) {
int tmo = 200000; /* 2 sec */
while(1) {
if(dregs->csr & CSR_FIFO_EMPTY)
break;
if(--tmo <= 0)
return 1;
udelay(10);
}
}
count = sun3scsi_dma_count(default_instance);
#ifdef OLDDMA
/* if we've finished a read, copy out the data we read */
if(sun3_dma_orig_addr) {
/* check for residual bytes after dma end */
if(count && (NCR5380_read(BUS_AND_STATUS_REG) &
(BASR_PHASE_MATCH | BASR_ACK))) {
printk("scsi%d: sun3_scsi_finish: read overrun baby... ", default_instance->host_no);
printk("basr now %02x\n", NCR5380_read(BUS_AND_STATUS_REG));
ret = count;
}
/* copy in what we dma'd no matter what */
memcpy(sun3_dma_orig_addr, dmabuf, sun3_dma_orig_count);
sun3_dma_orig_addr = NULL;
}
#else
fifo = dregs->fifo_count;
last_residual = fifo;
/* empty bytes from the fifo which didn't make it */
if((!write_flag) && (count - fifo) == 2) {
unsigned short data;
unsigned char *vaddr;
data = dregs->fifo_data;
vaddr = (unsigned char *)dvma_btov(sun3_dma_orig_addr);
vaddr += (sun3_dma_orig_count - fifo);
vaddr[-2] = (data & 0xff00) >> 8;
vaddr[-1] = (data & 0xff);
}
dvma_unmap(sun3_dma_orig_addr);
#endif
sun3_udc_write(UDC_RESET, UDC_CSR);
dregs->fifo_count = 0;
dregs->csr &= ~CSR_SEND;
/* reset fifo */
dregs->csr &= ~CSR_FIFO;
dregs->csr |= CSR_FIFO;
sun3_dma_setup_done = NULL;
return ret;
}
#include "sun3_NCR5380.c"
static Scsi_Host_Template driver_template = SUN3_NCR5380;
#include "scsi_module.c"
|