Viewing file:  eata_dma.h (4.89 KB) -rw-r--r--
Select action/file-type:
 (+) |  (+) |  (+) | Code (+) | Session (+) |  (+) | SDB (+) |  (+) |  (+) |  (+) |  (+) |  (+) |
/********************************************************
* Header file for eata_dma.c Linux EATA-DMA SCSI driver *
* (c) 1993-96 Michael Neuffer *
* mike@i-Connect.Net *
* neuffer@mail.uni-mainz.de *
*********************************************************
* last change: 96/10/14 *
********************************************************/
#ifndef _EATA_DMA_H
#define _EATA_DMA_H
#include "eata_generic.h"
#define VER_MAJOR 2
#define VER_MINOR 5
#define VER_SUB "9b"
/************************************************************************
* Here you can switch parts of the code on and of *
************************************************************************/
#define CHECKPAL 0 /* EISA pal checking on/off */
#define CHECK_BLINK 1 /* Switch Blink state check off, might *
* be nessessary for some MIPS machines*/
#define CRIPPLE_QUEUE 0 /* Only enable this if the interrupt
* controller on your motherboard is
* broken and you are experiencing
* massive interrupt losses */
/************************************************************************
* Debug options. *
* Enable DEBUG and whichever options you require. *
************************************************************************/
#define DEBUG_EATA 1 /* Enable debug code. */
#define DPT_DEBUG 0 /* Bobs special */
#define DBG_DELAY 0 /* Build in delays so debug messages can be
* be read before they vanish of the top of
* the screen! */
#define DBG_PROBE 0 /* Debug probe routines. */
#define DBG_PCI 0 /* Trace PCI routines */
#define DBG_EISA 0 /* Trace EISA routines */
#define DBG_ISA 0 /* Trace ISA routines */
#define DBG_BLINK 0 /* Trace Blink check */
#define DBG_PIO 0 /* Trace get_config_PIO */
#define DBG_COM 0 /* Trace command call */
#define DBG_QUEUE 0 /* Trace command queueing. */
#define DBG_QUEUE2 0 /* Trace command queueing SG. */
#define DBG_INTR 0 /* Trace interrupt service routine. */
#define DBG_INTR2 0 /* Trace interrupt service routine. */
#define DBG_INTR3 0 /* Trace get_board_data interrupts. */
#define DBG_REQSENSE 0 /* Trace request sense commands */
#define DBG_RESET 0 /* Trace reset calls */
#define DBG_STATUS 0 /* Trace status generation */
#define DBG_PROC 0 /* Debug proc-fs related statistics */
#define DBG_PROC_WRITE 0
#define DBG_REGISTER 0 /* */
#define DBG_ABNORM 1 /* Debug abnormal actions (reset, abort)*/
#if DEBUG_EATA
#define DBG(x, y) if ((x)) {y;}
#else
#define DBG(x, y)
#endif
int eata_detect(Scsi_Host_Template *);
const char *eata_info(struct Scsi_Host *);
int eata_command(Scsi_Cmnd *);
int eata_queue(Scsi_Cmnd *, void (* done)(Scsi_Cmnd *));
int eata_abort(Scsi_Cmnd *);
int eata_reset(Scsi_Cmnd *, unsigned int);
int eata_proc_info(char *, char **, off_t, int, int, int);
#ifdef MODULE
int eata_release(struct Scsi_Host *);
#else
#define eata_release NULL
#endif
#include <scsi/scsicam.h>
#define EATA_DMA { \
proc_info: eata_proc_info, /* procinfo */ \
name: "EATA (Extended Attachment) HBA driver", \
detect: eata_detect, \
release: eata_release, \
queuecommand: eata_queue, \
abort: eata_abort, \
reset: eata_reset, \
bios_param: scsicam_bios_param, \
unchecked_isa_dma: 1, /* True if ISA */ \
use_clustering: ENABLE_CLUSTERING }
#endif /* _EATA_DMA_H */
/*
* Overrides for Emacs so that we almost follow Linus's tabbing style.
* Emacs will notice this stuff at the end of the file and automatically
* adjust the settings for this buffer only. This must remain at the end
* of the file.
* ---------------------------------------------------------------------------
* Local variables:
* c-indent-level: 4
* c-brace-imaginary-offset: 0
* c-brace-offset: -4
* c-argdecl-indent: 4
* c-label-offset: -4
* c-continued-statement-offset: 4
* c-continued-brace-offset: 0
* indent-tabs-mode: nil
* tab-width: 8
* End:
*/
|