Viewing file:  a3000.c (5.88 KB) -rw-r--r--
Select action/file-type:
 (+) |  (+) |  (+) | Code (+) | Session (+) |  (+) | SDB (+) |  (+) |  (+) |  (+) |  (+) |  (+) |
#include <linux/types.h>
#include <linux/mm.h>
#include <linux/blk.h>
#include <linux/sched.h>
#include <linux/version.h>
#include <linux/ioport.h>
#include <linux/init.h>
#include <linux/spinlock.h>
#include <asm/setup.h>
#include <asm/page.h>
#include <asm/pgtable.h>
#include <asm/amigaints.h>
#include <asm/amigahw.h>
#include <asm/irq.h>
#include "scsi.h"
#include "hosts.h"
#include "wd33c93.h"
#include "a3000.h"
#include<linux/stat.h>
#define DMA(ptr) ((a3000_scsiregs *)((ptr)->base))
#define HDATA(ptr) ((struct WD33C93_hostdata *)((ptr)->hostdata))
static struct Scsi_Host *a3000_host = NULL;
static void a3000_intr (int irq, void *dummy, struct pt_regs *fp)
{
unsigned long flags;
unsigned int status = DMA(a3000_host)->ISTR;
if (!(status & ISTR_INT_P))
return;
if (status & ISTR_INTS)
{
spin_lock_irqsave(&io_request_lock, flags);
wd33c93_intr (a3000_host);
spin_unlock_irqrestore(&io_request_lock, flags);
} else
printk("Non-serviced A3000 SCSI-interrupt? ISTR = %02x\n",
status);
}
static int dma_setup (Scsi_Cmnd *cmd, int dir_in)
{
unsigned short cntr = CNTR_PDMD | CNTR_INTEN;
unsigned long addr = virt_to_bus(cmd->SCp.ptr);
/*
* if the physical address has the wrong alignment, or if
* physical address is bad, or if it is a write and at the
* end of a physical memory chunk, then allocate a bounce
* buffer
*/
if (addr & A3000_XFER_MASK ||
(!dir_in && mm_end_of_chunk (addr, cmd->SCp.this_residual)))
{
HDATA(a3000_host)->dma_bounce_len = (cmd->SCp.this_residual + 511)
& ~0x1ff;
HDATA(a3000_host)->dma_bounce_buffer =
scsi_malloc (HDATA(a3000_host)->dma_bounce_len);
/* can't allocate memory; use PIO */
if (!HDATA(a3000_host)->dma_bounce_buffer) {
HDATA(a3000_host)->dma_bounce_len = 0;
return 1;
}
if (!dir_in) {
/* copy to bounce buffer for a write */
if (cmd->use_sg) {
memcpy (HDATA(a3000_host)->dma_bounce_buffer,
cmd->SCp.ptr, cmd->SCp.this_residual);
} else
memcpy (HDATA(a3000_host)->dma_bounce_buffer,
cmd->request_buffer, cmd->request_bufflen);
}
addr = virt_to_bus(HDATA(a3000_host)->dma_bounce_buffer);
}
/* setup dma direction */
if (!dir_in)
cntr |= CNTR_DDIR;
/* remember direction */
HDATA(a3000_host)->dma_dir = dir_in;
DMA(a3000_host)->CNTR = cntr;
/* setup DMA *physical* address */
DMA(a3000_host)->ACR = addr;
if (dir_in)
/* invalidate any cache */
cache_clear (addr, cmd->SCp.this_residual);
else
/* push any dirty cache */
cache_push (addr, cmd->SCp.this_residual);
/* start DMA */
mb(); /* make sure setup is completed */
DMA(a3000_host)->ST_DMA = 1;
mb(); /* make sure DMA has started before next IO */
/* return success */
return 0;
}
static void dma_stop (struct Scsi_Host *instance, Scsi_Cmnd *SCpnt,
int status)
{
/* disable SCSI interrupts */
unsigned short cntr = CNTR_PDMD;
if (!HDATA(instance)->dma_dir)
cntr |= CNTR_DDIR;
DMA(instance)->CNTR = cntr;
mb(); /* make sure CNTR is updated before next IO */
/* flush if we were reading */
if (HDATA(instance)->dma_dir) {
DMA(instance)->FLUSH = 1;
mb(); /* don't allow prefetch */
while (!(DMA(instance)->ISTR & ISTR_FE_FLG))
barrier();
mb(); /* no IO until FLUSH is done */
}
/* clear a possible interrupt */
/* I think that this CINT is only necessary if you are
* using the terminal count features. HM 7 Mar 1994
*/
DMA(instance)->CINT = 1;
/* stop DMA */
DMA(instance)->SP_DMA = 1;
mb(); /* make sure DMA is stopped before next IO */
/* restore the CONTROL bits (minus the direction flag) */
DMA(instance)->CNTR = CNTR_PDMD | CNTR_INTEN;
mb(); /* make sure CNTR is updated before next IO */
/* copy from a bounce buffer, if necessary */
if (status && HDATA(instance)->dma_bounce_buffer) {
if (SCpnt && SCpnt->use_sg) {
if (HDATA(instance)->dma_dir && SCpnt)
memcpy (SCpnt->SCp.ptr,
HDATA(instance)->dma_bounce_buffer,
SCpnt->SCp.this_residual);
scsi_free (HDATA(instance)->dma_bounce_buffer,
HDATA(instance)->dma_bounce_len);
HDATA(instance)->dma_bounce_buffer = NULL;
HDATA(instance)->dma_bounce_len = 0;
} else {
if (HDATA(instance)->dma_dir && SCpnt)
memcpy (SCpnt->request_buffer,
HDATA(instance)->dma_bounce_buffer,
SCpnt->request_bufflen);
scsi_free (HDATA(instance)->dma_bounce_buffer,
HDATA(instance)->dma_bounce_len);
HDATA(instance)->dma_bounce_buffer = NULL;
HDATA(instance)->dma_bounce_len = 0;
}
}
}
int __init a3000_detect(Scsi_Host_Template *tpnt)
{
wd33c93_regs regs;
if (!MACH_IS_AMIGA || !AMIGAHW_PRESENT(A3000_SCSI))
return 0;
if (!request_mem_region(0xDD0000, 256, "wd33c93"))
return 0;
tpnt->proc_name = "A3000";
tpnt->proc_info = &wd33c93_proc_info;
a3000_host = scsi_register (tpnt, sizeof(struct WD33C93_hostdata));
if (a3000_host == NULL)
goto fail_register;
a3000_host->base = ZTWO_VADDR(0xDD0000);
a3000_host->irq = IRQ_AMIGA_PORTS;
DMA(a3000_host)->DAWR = DAWR_A3000;
regs.SASR = &(DMA(a3000_host)->SASR);
regs.SCMD = &(DMA(a3000_host)->SCMD);
wd33c93_init(a3000_host, regs, dma_setup, dma_stop, WD33C93_FS_12_15);
if (request_irq(IRQ_AMIGA_PORTS, a3000_intr, SA_SHIRQ, "A3000 SCSI",
a3000_intr))
goto fail_irq;
DMA(a3000_host)->CNTR = CNTR_PDMD | CNTR_INTEN;
return 1;
fail_irq:
#ifdef MODULE
wd33c93_release();
#endif /* MODULE */
scsi_unregister(a3000_host);
fail_register:
release_mem_region(0xDD0000, 256);
return 0;
}
#define HOSTS_C
static Scsi_Host_Template driver_template = _A3000_SCSI;
#include "scsi_module.c"
int __exit a3000_release(struct Scsi_Host *instance)
{
#ifdef MODULE
wd33c93_release();
#endif /* MODULE*/
DMA(instance)->CNTR = 0;
release_mem_region(0xDD0000, 256);
free_irq(IRQ_AMIGA_PORTS, a3000_intr);
return 1;
}
|