Viewing file:  specialix.c (62 KB) -rw-r--r--
Select action/file-type:
 (+) |  (+) |  (+) | Code (+) | Session (+) |  (+) | SDB (+) |  (+) |  (+) |  (+) |  (+) |  (+) |
/*
* specialix.c -- specialix IO8+ multiport serial driver.
*
* Copyright (C) 1997 Roger Wolff (R.E.Wolff@BitWizard.nl)
* Copyright (C) 1994-1996 Dmitry Gorodchanin (pgmdsg@ibi.com)
*
* Specialix pays for the development and support of this driver.
* Please DO contact io8-linux@specialix.co.uk if you require
* support. But please read the documentation (specialix.txt)
* first.
*
* This driver was developped in the BitWizard linux device
* driver service. If you require a linux device driver for your
* product, please contact devices@BitWizard.nl for a quote.
*
* This code is firmly based on the riscom/8 serial driver,
* written by Dmitry Gorodchanin. The specialix IO8+ card
* programming information was obtained from the CL-CD1865 Data
* Book, and Specialix document number 6200059: IO8+ Hardware
* Functional Specification.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be
* useful, but WITHOUT ANY WARRANTY; without even the implied
* warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR
* PURPOSE. See the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public
* License along with this program; if not, write to the Free
* Software Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139,
* USA.
*
* Revision history:
*
* Revision 1.0: April 1st 1997.
* Initial release for alpha testing.
* Revision 1.1: April 14th 1997.
* Incorporated Richard Hudsons suggestions,
* removed some debugging printk's.
* Revision 1.2: April 15th 1997.
* Ported to 2.1.x kernels.
* Revision 1.3: April 17th 1997
* Backported to 2.0. (Compatibility macros).
* Revision 1.4: April 18th 1997
* Fixed DTR/RTS bug that caused the card to indicate
* "don't send data" to a modem after the password prompt.
* Fixed bug for premature (fake) interrupts.
* Revision 1.5: April 19th 1997
* fixed a minor typo in the header file, cleanup a little.
* performance warnings are now MAXed at once per minute.
* Revision 1.6: May 23 1997
* Changed the specialix=... format to include interrupt.
* Revision 1.7: May 27 1997
* Made many more debug printk's a compile time option.
* Revision 1.8: Jul 1 1997
* port to linux-2.1.43 kernel.
* Revision 1.9: Oct 9 1998
* Added stuff for the IO8+/PCI version.
* Revision 1.10: Oct 22 1999 / Jan 21 2000.
* Added stuff for setserial.
* Nicolas Mailhot (Nicolas.Mailhot@email.enst.fr)
*
*/
#define VERSION "1.10"
/*
* There is a bunch of documentation about the card, jumpers, config
* settings, restrictions, cables, device names and numbers in
* ../../Documentation/specialix.txt
*/
#include <linux/config.h>
#include <linux/module.h>
#include <asm/io.h>
#include <linux/kernel.h>
#include <linux/sched.h>
#include <linux/ioport.h>
#include <linux/interrupt.h>
#include <linux/errno.h>
#include <linux/tty.h>
#include <linux/mm.h>
#include <linux/serial.h>
#include <linux/fcntl.h>
#include <linux/major.h>
#include <linux/delay.h>
#include <linux/tqueue.h>
#include <linux/version.h>
#include <linux/pci.h>
/* ************************************************************** */
/* * This section can be removed when 2.0 becomes outdated.... * */
/* ************************************************************** */
#if LINUX_VERSION_CODE < 131328 /* Less than 2.1.0 */
#define TWO_ZERO
#else
#if LINUX_VERSION_CODE < 131371 /* less than 2.1.43 */
/* This has not been extensively tested yet. Sorry. */
#warning "You're on your own between 2.1.0 and 2.1.43.... "
#warning "Please use a recent kernel."
#endif
#endif
#ifdef TWO_ZERO
#define Get_user(a,b) a = get_user(b)
#define copy_from_user(a,b,c) memcpy_fromfs(a,b,c)
#define copy_to_user(a,b,c) memcpy_tofs(a,b,c)
#define queue_task queue_task_irq_off
#else
#define Get_user(a,b) get_user(a,b)
#endif
/* ************************************************************** */
/* * End of compatibility section.. * */
/* ************************************************************** */
#ifndef TWO_ZERO
#include <asm/uaccess.h>
#endif
#include "specialix_io8.h"
#include "cd1865.h"
/* Configurable options: */
/* Am I paranoid or not ? ;-) */
#define SPECIALIX_PARANOIA_CHECK
/* Do I trust the IRQ from the card? (enabeling it doesn't seem to help)
When the IRQ routine leaves the chip in a state that is keeps on
requiring attention, the timer doesn't help either. */
#undef SPECIALIX_TIMER
/*
* The following defines are mostly for testing purposes. But if you need
* some nice reporting in your syslog, you can define them also.
*/
#undef SX_REPORT_FIFO
#undef SX_REPORT_OVERRUN
#ifdef CONFIG_SPECIALIX_RTSCTS
#define SX_CRTSCTS(bla) 1
#else
#define SX_CRTSCTS(tty) C_CRTSCTS(tty)
#endif
/* Used to be outb (0xff, 0x80); */
#define short_pause() udelay (1)
#define SPECIALIX_LEGAL_FLAGS \
(ASYNC_HUP_NOTIFY | ASYNC_SAK | ASYNC_SPLIT_TERMIOS | \
ASYNC_SPD_HI | ASYNC_SPEED_VHI | ASYNC_SESSION_LOCKOUT | \
ASYNC_PGRP_LOCKOUT | ASYNC_CALLOUT_NOHUP)
#ifndef MIN
#define MIN(a,b) ((a) < (b) ? (a) : (b))
#endif
DECLARE_TASK_QUEUE(tq_specialix);
#undef RS_EVENT_WRITE_WAKEUP
#define RS_EVENT_WRITE_WAKEUP 0
#define SPECIALIX_TYPE_NORMAL 1
#define SPECIALIX_TYPE_CALLOUT 2
static struct tty_driver specialix_driver, specialix_callout_driver;
static int specialix_refcount;
static struct tty_struct * specialix_table[SX_NBOARD * SX_NPORT];
static struct termios * specialix_termios[SX_NBOARD * SX_NPORT];
static struct termios * specialix_termios_locked[SX_NBOARD * SX_NPORT];
static unsigned char * tmp_buf;
static DECLARE_MUTEX(tmp_buf_sem);
static unsigned long baud_table[] = {
0, 50, 75, 110, 134, 150, 200, 300, 600, 1200, 1800, 2400, 4800,
9600, 19200, 38400, 57600, 115200, 0,
};
static struct specialix_board sx_board[SX_NBOARD] = {
{ 0, SX_IOBASE1, 9, },
{ 0, SX_IOBASE2, 11, },
{ 0, SX_IOBASE3, 12, },
{ 0, SX_IOBASE4, 15, },
};
static struct specialix_port sx_port[SX_NBOARD * SX_NPORT];
#ifdef SPECIALIX_TIMER
static struct timer_list missed_irq_timer;
static void sx_interrupt(int irq, void * dev_id, struct pt_regs * regs);
#endif
static inline int sx_paranoia_check(struct specialix_port const * port,
kdev_t device, const char *routine)
{
#ifdef SPECIALIX_PARANOIA_CHECK
static const char *badmagic =
KERN_ERR "sx: Warning: bad specialix port magic number for device %s in %s\n";
static const char *badinfo =
KERN_ERR "sx: Warning: null specialix port for device %s in %s\n";
if (!port) {
printk(badinfo, kdevname(device), routine);
return 1;
}
if (port->magic != SPECIALIX_MAGIC) {
printk(badmagic, kdevname(device), routine);
return 1;
}
#endif
return 0;
}
/*
*
* Service functions for specialix IO8+ driver.
*
*/
/* Get board number from pointer */
extern inline int board_No (struct specialix_board * bp)
{
return bp - sx_board;
}
/* Get port number from pointer */
extern inline int port_No (struct specialix_port const * port)
{
return SX_PORT(port - sx_port);
}
/* Get pointer to board from pointer to port */
extern inline struct specialix_board * port_Board(struct specialix_port const * port)
{
return &sx_board[SX_BOARD(port - sx_port)];
}
/* Input Byte from CL CD186x register */
extern inline unsigned char sx_in(struct specialix_board * bp, unsigned short reg)
{
bp->reg = reg | 0x80;
outb (reg | 0x80, bp->base + SX_ADDR_REG);
return inb (bp->base + SX_DATA_REG);
}
/* Output Byte to CL CD186x register */
extern inline void sx_out(struct specialix_board * bp, unsigned short reg,
unsigned char val)
{
bp->reg = reg | 0x80;
outb (reg | 0x80, bp->base + SX_ADDR_REG);
outb (val, bp->base + SX_DATA_REG);
}
/* Input Byte from CL CD186x register */
extern inline unsigned char sx_in_off(struct specialix_board * bp, unsigned short reg)
{
bp->reg = reg;
outb (reg, bp->base + SX_ADDR_REG);
return inb (bp->base + SX_DATA_REG);
}
/* Output Byte to CL CD186x register */
extern inline void sx_out_off(struct specialix_board * bp, unsigned short reg,
unsigned char val)
{
bp->reg = reg;
outb (reg, bp->base + SX_ADDR_REG);
outb (val, bp->base + SX_DATA_REG);
}
/* Wait for Channel Command Register ready */
extern inline void sx_wait_CCR(struct specialix_board * bp)
{
unsigned long delay;
for (delay = SX_CCR_TIMEOUT; delay; delay--)
if (!sx_in(bp, CD186x_CCR))
return;
printk(KERN_ERR "sx%d: Timeout waiting for CCR.\n", board_No(bp));
}
/* Wait for Channel Command Register ready */
extern inline void sx_wait_CCR_off(struct specialix_board * bp)
{
unsigned long delay;
for (delay = SX_CCR_TIMEOUT; delay; delay--)
if (!sx_in_off(bp, CD186x_CCR))
return;
printk(KERN_ERR "sx%d: Timeout waiting for CCR.\n", board_No(bp));
}
/*
* specialix IO8+ IO range functions.
*/
extern inline int sx_check_io_range(struct specialix_board * bp)
{
return check_region (bp->base, SX_IO_SPACE);
}
extern inline void sx_request_io_range(struct specialix_board * bp)
{
request_region(bp->base,
bp->flags&SX_BOARD_IS_PCI?SX_PCI_IO_SPACE:SX_IO_SPACE,
"specialix IO8+" );
}
extern inline void sx_release_io_range(struct specialix_board * bp)
{
release_region(bp->base,
bp->flags&SX_BOARD_IS_PCI?SX_PCI_IO_SPACE:SX_IO_SPACE);
}
/* Must be called with enabled interrupts */
/* Ugly. Very ugly. Don't use this for anything else than initialization
code */
extern inline void sx_long_delay(unsigned long delay)
{
unsigned long i;
for (i = jiffies + delay; time_after(i, jiffies); ) ;
}
/* Set the IRQ using the RTS lines that run to the PAL on the board.... */
int sx_set_irq ( struct specialix_board *bp)
{
int virq;
int i;
if (bp->flags & SX_BOARD_IS_PCI)
return 1;
switch (bp->irq) {
/* In the same order as in the docs... */
case 15: virq = 0;break;
case 12: virq = 1;break;
case 11: virq = 2;break;
case 9: virq = 3;break;
default: printk (KERN_ERR "Speclialix: cannot set irq to %d.\n", bp->irq);
return 0;
}
for (i=0;i<2;i++) {
sx_out(bp, CD186x_CAR, i);
sx_out(bp, CD186x_MSVRTS, ((virq >> i) & 0x1)? MSVR_RTS:0);
}
return 1;
}
/* Reset and setup CD186x chip */
static int sx_init_CD186x(struct specialix_board * bp)
{
unsigned long flags;
int scaler;
int rv = 1;
save_flags(flags); cli();
sx_wait_CCR_off(bp); /* Wait for CCR ready */
sx_out_off(bp, CD186x_CCR, CCR_HARDRESET); /* Reset CD186x chip */
sti();
sx_long_delay(HZ/20); /* Delay 0.05 sec */
cli();
sx_out_off(bp, CD186x_GIVR, SX_ID); /* Set ID for this chip */
sx_out_off(bp, CD186x_GICR, 0); /* Clear all bits */
sx_out_off(bp, CD186x_PILR1, SX_ACK_MINT); /* Prio for modem intr */
sx_out_off(bp, CD186x_PILR2, SX_ACK_TINT); /* Prio for transmitter intr */
sx_out_off(bp, CD186x_PILR3, SX_ACK_RINT); /* Prio for receiver intr */
/* Set RegAckEn */
sx_out_off(bp, CD186x_SRCR, sx_in (bp, CD186x_SRCR) | SRCR_REGACKEN);
/* Setting up prescaler. We need 4 ticks per 1 ms */
scaler = SX_OSCFREQ/SPECIALIX_TPS;
sx_out_off(bp, CD186x_PPRH, scaler >> 8);
sx_out_off(bp, CD186x_PPRL, scaler & 0xff);
if (!sx_set_irq (bp)) {
/* Figure out how to pass this along... */
printk (KERN_ERR "Cannot set irq to %d.\n", bp->irq);
rv = 0;
}
restore_flags(flags);
return rv;
}
int read_cross_byte (struct specialix_board *bp, int reg, int bit)
{
int i;
int t;
for (i=0, t=0;i<8;i++) {
sx_out_off (bp, CD186x_CAR, i);
if (sx_in_off (bp, reg) & bit)
t |= 1 << i;
}
return t;
}
#ifdef SPECIALIX_TIMER
void missed_irq (unsigned long data)
{
if (sx_in ((struct specialix_board *)data, CD186x_SRSR) &
(SRSR_RREQint |
SRSR_TREQint |
SRSR_MREQint)) {
printk (KERN_INFO "Missed interrupt... Calling int from timer. \n");
sx_interrupt (((struct specialix_board *)data)->irq,
NULL, NULL);
}
missed_irq_timer.expires = jiffies + HZ;
add_timer (&missed_irq_timer);
}
#endif
/* Main probing routine, also sets irq. */
static int sx_probe(struct specialix_board *bp)
{
unsigned char val1, val2;
#if 0
int irqs = 0;
int retries;
#endif
int rev;
int chip;
if (sx_check_io_range(bp))
return 1;
/* Are the I/O ports here ? */
sx_out_off(bp, CD186x_PPRL, 0x5a);
short_pause ();
val1 = sx_in_off(bp, CD186x_PPRL);
sx_out_off(bp, CD186x_PPRL, 0xa5);
short_pause ();
val2 = sx_in_off(bp, CD186x_PPRL);
if ((val1 != 0x5a) || (val2 != 0xa5)) {
printk(KERN_INFO "sx%d: specialix IO8+ Board at 0x%03x not found.\n",
board_No(bp), bp->base);
return 1;
}
/* Check the DSR lines that Specialix uses as board
identification */
val1 = read_cross_byte (bp, CD186x_MSVR, MSVR_DSR);
val2 = read_cross_byte (bp, CD186x_MSVR, MSVR_RTS);
#ifdef SPECIALIX_DEBUG
printk (KERN_DEBUG "sx%d: DSR lines are: %02x, rts lines are: %02x\n",
board_No(bp), val1, val2);
#endif
/* They managed to switch the bit order between the docs and
the IO8+ card. The new PCI card now conforms to old docs.
They changed the PCI docs to reflect the situation on the
old card. */
val2 = (bp->flags & SX_BOARD_IS_PCI)?0x4d : 0xb2;
if (val1 != val2) {
printk(KERN_INFO "sx%d: specialix IO8+ ID %02x at 0x%03x not found (%02x).\n",
board_No(bp), val2, bp->base, val1);
return 1;
}
#if 0
/* It's time to find IRQ for this board */
for (retries = 0; retries < 5 && irqs <= 0; retries++) {
irqs = probe_irq_on();
sx_init_CD186x(bp); /* Reset CD186x chip */
sx_out(bp, CD186x_CAR, 2); /* Select port 2 */
sx_wait_CCR(bp);
sx_out(bp, CD186x_CCR, CCR_TXEN); /* Enable transmitter */
sx_out(bp, CD186x_IER, IER_TXRDY); /* Enable tx empty intr */
sx_long_delay(HZ/20);
irqs = probe_irq_off(irqs);
#if SPECIALIX_DEBUG > 2
printk (KERN_DEBUG "SRSR = %02x, ", sx_in(bp, CD186x_SRSR));
printk ( "TRAR = %02x, ", sx_in(bp, CD186x_TRAR));
printk ( "GIVR = %02x, ", sx_in(bp, CD186x_GIVR));
printk ( "GICR = %02x, ", sx_in(bp, CD186x_GICR));
printk ( "\n");
#endif
/* Reset CD186x again */
if (!sx_init_CD186x(bp)) {
/* Hmmm. This is dead code anyway. */
}
#if SPECIALIX_DEBUG > 2
printk (KERN_DEBUG "val1 = %02x, val2 = %02x, val3 = %02x.\n",
val1, val2, val3);
#endif
}
#if 0
if (irqs <= 0) {
printk(KERN_ERR "sx%d: Can't find IRQ for specialix IO8+ board at 0x%03x.\n",
board_No(bp), bp->base);
return 1;
}
#endif
printk (KERN_INFO "Started with irq=%d, but now have irq=%d.\n", bp->irq, irqs);
if (irqs > 0)
bp->irq = irqs;
#endif
/* Reset CD186x again */
if (!sx_init_CD186x(bp)) {
return -EIO;
}
sx_request_io_range(bp);
bp->flags |= SX_BOARD_PRESENT;
/* Chip revcode pkgtype
GFRCR SRCR bit 7
CD180 rev B 0x81 0
CD180 rev C 0x82 0
CD1864 rev A 0x82 1
CD1865 rev A 0x83 1 -- Do not use!!! Does not work.
CD1865 rev B 0x84 1
-- Thanks to Gwen Wang, Cirrus Logic.
*/
switch (sx_in_off(bp, CD186x_GFRCR)) {
case 0x82:chip = 1864;rev='A';break;
case 0x83:chip = 1865;rev='A';break;
case 0x84:chip = 1865;rev='B';break;
case 0x85:chip = 1865;rev='C';break; /* Does not exist at this time */
default:chip=-1;rev='x';
}
#if SPECIALIX_DEBUG > 2
printk (KERN_DEBUG " GFCR = 0x%02x\n", sx_in_off(bp, CD186x_GFRCR) );
#endif
#ifdef SPECIALIX_TIMER
init_timer (&missed_irq_timer);
missed_irq_timer.function = missed_irq;
missed_irq_timer.data = (unsigned long) bp;
missed_irq_timer.expires = jiffies + HZ;
add_timer (&missed_irq_timer);
#endif
printk(KERN_INFO"sx%d: specialix IO8+ board detected at 0x%03x, IRQ %d, CD%d Rev. %c.\n",
board_No(bp),
bp->base, bp->irq,
chip, rev);
return 0;
}
/*
*
* Interrupt processing routines.
* */
extern inline void sx_mark_event(struct specialix_port * port, int event)
{
/*
* I'm not quite happy with current scheme all serial
* drivers use their own BH routine.
* It seems this easily can be done with one BH routine
* serving for all serial drivers.
* For now I must introduce another one - SPECIALIX_BH.
* Still hope this will be changed in near future.
* -- Dmitry.
*/
set_bit(event, &port->event);
queue_task(&port->tqueue, &tq_specialix);
mark_bh(SPECIALIX_BH);
}
extern inline struct specialix_port * sx_get_port(struct specialix_board * bp,
unsigned char const * what)
{
unsigned char channel;
struct specialix_port * port;
channel = sx_in(bp, CD186x_GICR) >> GICR_CHAN_OFF;
if (channel < CD186x_NCH) {
port = &sx_port[board_No(bp) * SX_NPORT + channel];
if (port->flags & ASYNC_INITIALIZED) {
return port;
}
}
printk(KERN_INFO "sx%d: %s interrupt from invalid port %d\n",
board_No(bp), what, channel);
return NULL;
}
extern inline void sx_receive_exc(struct specialix_board * bp)
{
struct specialix_port *port;
struct tty_struct *tty;
unsigned char status;
unsigned char ch;
if (!(port = sx_get_port(bp, "Receive")))
return;
tty = port->tty;
if (tty->flip.count >= TTY_FLIPBUF_SIZE) {
printk(KERN_INFO "sx%d: port %d: Working around flip buffer overflow.\n",
board_No(bp), port_No(port));
return;
}
#ifdef SX_REPORT_OVERRUN
status = sx_in(bp, CD186x_RCSR);
if (status & RCSR_OE) {
port->overrun++;
#if SPECIALIX_DEBUG
printk(KERN_DEBUG "sx%d: port %d: Overrun. Total %ld overruns.\n",
board_No(bp), port_No(port), port->overrun);
#endif
}
status &= port->mark_mask;
#else
status = sx_in(bp, CD186x_RCSR) & port->mark_mask;
#endif
ch = sx_in(bp, CD186x_RDR);
if (!status) {
return;
}
if (status & RCSR_TOUT) {
printk(KERN_INFO "sx%d: port %d: Receiver timeout. Hardware problems ?\n",
board_No(bp), port_No(port));
return;
} else if (status & RCSR_BREAK) {
#ifdef SPECIALIX_DEBUG
printk(KERN_DEBUG "sx%d: port %d: Handling break...\n",
board_No(bp), port_No(port));
#endif
*tty->flip.flag_buf_ptr++ = TTY_BREAK;
if (port->flags & ASYNC_SAK)
do_SAK(tty);
} else if (status & RCSR_PE)
*tty->flip.flag_buf_ptr++ = TTY_PARITY;
else if (status & RCSR_FE)
*tty->flip.flag_buf_ptr++ = TTY_FRAME;
else if (status & RCSR_OE)
*tty->flip.flag_buf_ptr++ = TTY_OVERRUN;
else
*tty->flip.flag_buf_ptr++ = 0;
*tty->flip.char_buf_ptr++ = ch;
tty->flip.count++;
queue_task(&tty->flip.tqueue, &tq_timer);
}
extern inline void sx_receive(struct specialix_board * bp)
{
struct specialix_port *port;
struct tty_struct *tty;
unsigned char count;
if (!(port = sx_get_port(bp, "Receive")))
return;
tty = port->tty;
count = sx_in(bp, CD186x_RDCR);
#ifdef SX_REPORT_FIFO
port->hits[count > 8 ? 9 : count]++;
#endif
while (count--) {
if (tty->flip.count >= TTY_FLIPBUF_SIZE) {
printk(KERN_INFO "sx%d: port %d: Working around flip buffer overflow.\n",
board_No(bp), port_No(port));
break;
}
*tty->flip.char_buf_ptr++ = sx_in(bp, CD186x_RDR);
*tty->flip.flag_buf_ptr++ = 0;
tty->flip.count++;
}
queue_task(&tty->flip.tqueue, &tq_timer);
}
extern inline void sx_transmit(struct specialix_board * bp)
{
struct specialix_port *port;
struct tty_struct *tty;
unsigned char count;
if (!(port = sx_get_port(bp, "Transmit")))
return;
tty = port->tty;
if (port->IER & IER_TXEMPTY) {
/* FIFO drained */
sx_out(bp, CD186x_CAR, port_No(port));
port->IER &= ~IER_TXEMPTY;
sx_out(bp, CD186x_IER, port->IER);
return;
}
if ((port->xmit_cnt <= 0 && !port->break_length)
|| tty->stopped || tty->hw_stopped) {
sx_out(bp, CD186x_CAR, port_No(port));
port->IER &= ~IER_TXRDY;
sx_out(bp, CD186x_IER, port->IER);
return;
}
if (port->break_length) {
if (port->break_length > 0) {
if (port->COR2 & COR2_ETC) {
sx_out(bp, CD186x_TDR, CD186x_C_ESC);
sx_out(bp, CD186x_TDR, CD186x_C_SBRK);
port->COR2 &= ~COR2_ETC;
}
count = MIN(port->break_length, 0xff);
sx_out(bp, CD186x_TDR, CD186x_C_ESC);
sx_out(bp, CD186x_TDR, CD186x_C_DELAY);
sx_out(bp, CD186x_TDR, count);
if (!(port->break_length -= count))
port->break_length--;
} else {
sx_out(bp, CD186x_TDR, CD186x_C_ESC);
sx_out(bp, CD186x_TDR, CD186x_C_EBRK);
sx_out(bp, CD186x_COR2, port->COR2);
sx_wait_CCR(bp);
sx_out(bp, CD186x_CCR, CCR_CORCHG2);
port->break_length = 0;
}
return;
}
count = CD186x_NFIFO;
do {
sx_out(bp, CD186x_TDR, port->xmit_buf[port->xmit_tail++]);
port->xmit_tail = port->xmit_tail & (SERIAL_XMIT_SIZE-1);
if (--port->xmit_cnt <= 0)
break;
} while (--count > 0);
if (port->xmit_cnt <= 0) {
sx_out(bp, CD186x_CAR, port_No(port));
port->IER &= ~IER_TXRDY;
sx_out(bp, CD186x_IER, port->IER);
}
if (port->xmit_cnt <= port->wakeup_chars)
sx_mark_event(port, RS_EVENT_WRITE_WAKEUP);
}
extern inline void sx_check_modem(struct specialix_board * bp)
{
struct specialix_port *port;
struct tty_struct *tty;
unsigned char mcr;
#ifdef SPECIALIX_DEBUG
printk (KERN_DEBUG "Modem intr. ");
#endif
if (!(port = sx_get_port(bp, "Modem")))
return;
tty = port->tty;
mcr = sx_in(bp, CD186x_MCR);
printk ("mcr = %02x.\n", mcr);
if ((mcr & MCR_CDCHG)) {
#ifdef SPECIALIX_DEBUG
printk (KERN_DEBUG "CD just changed... ");
#endif
if (sx_in(bp, CD186x_MSVR) & MSVR_CD) {
#ifdef SPECIALIX_DEBUG
printk ( "Waking up guys in open.\n");
#endif
wake_up_interruptible(&port->open_wait);
}
else if (!((port->flags & ASYNC_CALLOUT_ACTIVE) &&
(port->flags & ASYNC_CALLOUT_NOHUP))) {
#ifdef SPECIALIX_DEBUG
printk ( "Sending HUP.\n");
#endif
MOD_INC_USE_COUNT;
if (schedule_task(&port->tqueue_hangup) == 0)
MOD_DEC_USE_COUNT;
} else {
#ifdef SPECIALIX_DEBUG
printk ( "Don't need to send HUP.\n");
#endif
}
}
#ifdef SPECIALIX_BRAIN_DAMAGED_CTS
if (mcr & MCR_CTSCHG) {
if (sx_in(bp, CD186x_MSVR) & MSVR_CTS) {
tty->hw_stopped = 0;
port->IER |= IER_TXRDY;
if (port->xmit_cnt <= port->wakeup_chars)
sx_mark_event(port, RS_EVENT_WRITE_WAKEUP);
} else {
tty->hw_stopped = 1;
port->IER &= ~IER_TXRDY;
}
sx_out(bp, CD186x_IER, port->IER);
}
if (mcr & MCR_DSSXHG) {
if (sx_in(bp, CD186x_MSVR) & MSVR_DSR) {
tty->hw_stopped = 0;
port->IER |= IER_TXRDY;
if (port->xmit_cnt <= port->wakeup_chars)
sx_mark_event(port, RS_EVENT_WRITE_WAKEUP);
} else {
tty->hw_stopped = 1;
port->IER &= ~IER_TXRDY;
}
sx_out(bp, CD186x_IER, port->IER);
}
#endif /* SPECIALIX_BRAIN_DAMAGED_CTS */
/* Clear change bits */
sx_out(bp, CD186x_MCR, 0);
}
/* The main interrupt processing routine */
static void sx_interrupt(int irq, void * dev_id, struct pt_regs * regs)
{
unsigned char status;
unsigned char ack;
struct specialix_board *bp;
unsigned long loop = 0;
int saved_reg;
bp = dev_id;
if (!bp || !(bp->flags & SX_BOARD_ACTIVE)) {
#ifdef SPECIALIX_DEBUG
printk (KERN_DEBUG "sx: False interrupt. irq %d.\n", irq);
#endif
return;
}
saved_reg = bp->reg;
while ((++loop < 16) && (status = (sx_in(bp, CD186x_SRSR) &
(SRSR_RREQint |
SRSR_TREQint |
SRSR_MREQint)))) {
if (status & SRSR_RREQint) {
ack = sx_in(bp, CD186x_RRAR);
if (ack == (SX_ID | GIVR_IT_RCV))
sx_receive(bp);
else if (ack == (SX_ID | GIVR_IT_REXC))
sx_receive_exc(bp);
else
printk(KERN_ERR "sx%d: Bad receive ack 0x%02x.\n",
board_No(bp), ack);
} else if (status & SRSR_TREQint) {
ack = sx_in(bp, CD186x_TRAR);
if (ack == (SX_ID | GIVR_IT_TX))
sx_transmit(bp);
else
printk(KERN_ERR "sx%d: Bad transmit ack 0x%02x.\n",
board_No(bp), ack);
} else if (status & SRSR_MREQint) {
ack = sx_in(bp, CD186x_MRAR);
if (ack == (SX_ID | GIVR_IT_MODEM))
sx_check_modem(bp);
else
printk(KERN_ERR "sx%d: Bad modem ack 0x%02x.\n",
board_No(bp), ack);
}
sx_out(bp, CD186x_EOIR, 0); /* Mark end of interrupt */
}
bp->reg = saved_reg;
outb (bp->reg, bp->base + SX_ADDR_REG);
}
/*
* Routines for open & close processing.
*/
void turn_ints_off (struct specialix_board *bp)
{
if (bp->flags & SX_BOARD_IS_PCI) {
/* This was intended for enabeling the interrupt on the
* PCI card. However it seems that it's already enabled
* and as PCI interrupts can be shared, there is no real
* reason to have to turn it off. */
}
(void) sx_in_off (bp, 0); /* Turn off interrupts. */
}
void turn_ints_on (struct specialix_board *bp)
{
if (bp->flags & SX_BOARD_IS_PCI) {
/* play with the PCI chip. See comment above. */
}
(void) sx_in (bp, 0); /* Turn ON interrupts. */
}
/* Called with disabled interrupts */
extern inline int sx_setup_board(struct specialix_board * bp)
{
int error;
if (bp->flags & SX_BOARD_ACTIVE)
return 0;
if (bp->flags & SX_BOARD_IS_PCI)
error = request_irq(bp->irq, sx_interrupt, SA_INTERRUPT | SA_SHIRQ, "specialix IO8+", bp);
else
error = request_irq(bp->irq, sx_interrupt, SA_INTERRUPT, "specialix IO8+", bp);
if (error)
return error;
turn_ints_on (bp);
bp->flags |= SX_BOARD_ACTIVE;
MOD_INC_USE_COUNT;
return 0;
}
/* Called with disabled interrupts */
extern inline void sx_shutdown_board(struct specialix_board *bp)
{
if (!(bp->flags & SX_BOARD_ACTIVE))
return;
bp->flags &= ~SX_BOARD_ACTIVE;
#if SPECIALIX_DEBUG > 2
printk ("Freeing IRQ%d for board %d.\n", bp->irq, board_No (bp));
#endif
free_irq(bp->irq, bp);
turn_ints_off (bp);
MOD_DEC_USE_COUNT;
}
/*
* Setting up port characteristics.
* Must be called with disabled interrupts
*/
static void sx_change_speed(struct specialix_board *bp, struct specialix_port *port)
{
struct tty_struct *tty;
unsigned long baud;
long tmp;
unsigned char cor1 = 0, cor3 = 0;
unsigned char mcor1 = 0, mcor2 = 0;
static int again;
if (!(tty = port->tty) || !tty->termios)
return;
port->IER = 0;
port->COR2 = 0;
/* Select port on the board */
sx_out(bp, CD186x_CAR, port_No(port));
/* The Specialix board doens't implement the RTS lines.
They are used to set the IRQ level. Don't touch them. */
if (SX_CRTSCTS(tty))
port->MSVR = MSVR_DTR | (sx_in(bp, CD186x_MSVR) & MSVR_RTS);
else
port->MSVR = (sx_in(bp, CD186x_MSVR) & MSVR_RTS);
#ifdef DEBUG_SPECIALIX
printk (KERN_DEBUG "sx: got MSVR=%02x.\n", port->MSVR);
#endif
baud = C_BAUD(tty);
if (baud & CBAUDEX) {
baud &= ~CBAUDEX;
if (baud < 1 || baud > 2)
port->tty->termios->c_cflag &= ~CBAUDEX;
else
baud += 15;
}
if (baud == 15) {
if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI)
baud ++;
if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI)
baud += 2;
}
if (!baud_table[baud]) {
/* Drop DTR & exit */
#ifdef SPECIALIX_DEBUG
printk (KERN_DEBUG "Dropping DTR... Hmm....\n");
#endif
if (!SX_CRTSCTS (tty)) {
port -> MSVR &= ~ MSVR_DTR;
sx_out(bp, CD186x_MSVR, port->MSVR );
}
#ifdef DEBUG_SPECIALIX
else
printk (KERN_DEBUG "Can't drop DTR: no DTR.\n");
#endif
return;
} else {
/* Set DTR on */
if (!SX_CRTSCTS (tty)) {
port ->MSVR |= MSVR_DTR;
}
}
/*
* Now we must calculate some speed depended things
*/
/* Set baud rate for port */
tmp = port->custom_divisor ;
if ( tmp )
printk (KERN_INFO "sx%d: Using custom baud rate divisor %ld. \n"
"This is an untested option, please be carefull.\n",
port_No (port), tmp);
else
tmp = (((SX_OSCFREQ + baud_table[baud]/2) / baud_table[baud] +
CD186x_TPC/2) / CD186x_TPC);
if ((tmp < 0x10) && time_before(again, jiffies)) {
again = jiffies + HZ * 60;
/* Page 48 of version 2.0 of the CL-CD1865 databook */
if (tmp >= 12) {
printk (KERN_INFO "sx%d: Baud rate divisor is %ld. \n"
"Performance degradation is possible.\n"
"Read specialix.txt for more info.\n",
port_No (port), tmp);
} else {
printk (KERN_INFO "sx%d: Baud rate divisor is %ld. \n"
"Warning: overstressing Cirrus chip. "
"This might not work.\n"
"Read specialix.txt for more info.\n",
port_No (port), tmp);
}
}
sx_out(bp, CD186x_RBPRH, (tmp >> 8) & 0xff);
sx_out(bp, CD186x_TBPRH, (tmp >> 8) & 0xff);
sx_out(bp, CD186x_RBPRL, tmp & 0xff);
sx_out(bp, CD186x_TBPRL, tmp & 0xff);
if (port->custom_divisor) {
baud = (SX_OSCFREQ + port->custom_divisor/2) / port->custom_divisor;
baud = ( baud + 5 ) / 10;
} else
baud = (baud_table[baud] + 5) / 10; /* Estimated CPS */
/* Two timer ticks seems enough to wakeup something like SLIP driver */
tmp = ((baud + HZ/2) / HZ) * 2 - CD186x_NFIFO;
port->wakeup_chars = (tmp < 0) ? 0 : ((tmp >= SERIAL_XMIT_SIZE) ?
SERIAL_XMIT_SIZE - 1 : tmp);
/* Receiver timeout will be transmission time for 1.5 chars */
tmp = (SPECIALIX_TPS + SPECIALIX_TPS/2 + baud/2) / baud;
tmp = (tmp > 0xff) ? 0xff : tmp;
sx_out(bp, CD186x_RTPR, tmp);
switch (C_CSIZE(tty)) {
case CS5:
cor1 |= COR1_5BITS;
break;
case CS6:
cor1 |= COR1_6BITS;
break;
case CS7:
cor1 |= COR1_7BITS;
break;
case CS8:
cor1 |= COR1_8BITS;
break;
}
if (C_CSTOPB(tty))
cor1 |= COR1_2SB;
cor1 |= COR1_IGNORE;
if (C_PARENB(tty)) {
cor1 |= COR1_NORMPAR;
if (C_PARODD(tty))
cor1 |= COR1_ODDP;
if (I_INPCK(tty))
cor1 &= ~COR1_IGNORE;
}
/* Set marking of some errors */
port->mark_mask = RCSR_OE | RCSR_TOUT;
if (I_INPCK(tty))
port->mark_mask |= RCSR_FE | RCSR_PE;
if (I_BRKINT(tty) || I_PARMRK(tty))
port->mark_mask |= RCSR_BREAK;
if (I_IGNPAR(tty))
port->mark_mask &= ~(RCSR_FE | RCSR_PE);
if (I_IGNBRK(tty)) {
port->mark_mask &= ~RCSR_BREAK;
if (I_IGNPAR(tty))
/* Real raw mode. Ignore all */
port->mark_mask &= ~RCSR_OE;
}
/* Enable Hardware Flow Control */
if (C_CRTSCTS(tty)) {
#ifdef SPECIALIX_BRAIN_DAMAGED_CTS
port->IER |= IER_DSR | IER_CTS;
mcor1 |= MCOR1_DSRZD | MCOR1_CTSZD;
mcor2 |= MCOR2_DSROD | MCOR2_CTSOD;
tty->hw_stopped = !(sx_in(bp, CD186x_MSVR) & (MSVR_CTS|MSVR_DSR));
#else
port->COR2 |= COR2_CTSAE;
#endif
}
/* Enable Software Flow Control. FIXME: I'm not sure about this */
/* Some people reported that it works, but I still doubt it */
if (I_IXON(tty)) {
port->COR2 |= COR2_TXIBE;
cor3 |= (COR3_FCT | COR3_SCDE);
if (I_IXANY(tty))
port->COR2 |= COR2_IXM;
sx_out(bp, CD186x_SCHR1, START_CHAR(tty));
sx_out(bp, CD186x_SCHR2, STOP_CHAR(tty));
sx_out(bp, CD186x_SCHR3, START_CHAR(tty));
sx_out(bp, CD186x_SCHR4, STOP_CHAR(tty));
}
if (!C_CLOCAL(tty)) {
/* Enable CD check */
port->IER |= IER_CD;
mcor1 |= MCOR1_CDZD;
mcor2 |= MCOR2_CDOD;
}
if (C_CREAD(tty))
/* Enable receiver */
port->IER |= IER_RXD;
/* Set input FIFO size (1-8 bytes) */
cor3 |= SPECIALIX_RXFIFO;
/* Setting up CD186x channel registers */
sx_out(bp, CD186x_COR1, cor1);
sx_out(bp, CD186x_COR2, port->COR2);
sx_out(bp, CD186x_COR3, cor3);
/* Make CD186x know about registers change */
sx_wait_CCR(bp);
sx_out(bp, CD186x_CCR, CCR_CORCHG1 | CCR_CORCHG2 | CCR_CORCHG3);
/* Setting up modem option registers */
#ifdef DEBUG_SPECIALIX
printk ("Mcor1 = %02x, mcor2 = %02x.\n", mcor1, mcor2);
#endif
sx_out(bp, CD186x_MCOR1, mcor1);
sx_out(bp, CD186x_MCOR2, mcor2);
/* Enable CD186x transmitter & receiver */
sx_wait_CCR(bp);
sx_out(bp, CD186x_CCR, CCR_TXEN | CCR_RXEN);
/* Enable interrupts */
sx_out(bp, CD186x_IER, port->IER);
/* And finally set the modem lines... */
sx_out(bp, CD186x_MSVR, port->MSVR);
}
/* Must be called with interrupts enabled */
static int sx_setup_port(struct specialix_board *bp, struct specialix_port *port)
{
unsigned long flags;
if (port->flags & ASYNC_INITIALIZED)
return 0;
if (!port->xmit_buf) {
/* We may sleep in get_free_page() */
unsigned long tmp;
if (!(tmp = get_free_page(GFP_KERNEL)))
return -ENOMEM;
if (port->xmit_buf) {
free_page(tmp);
return -ERESTARTSYS;
}
port->xmit_buf = (unsigned char *) tmp;
}
save_flags(flags); cli();
if (port->tty)
clear_bit(TTY_IO_ERROR, &port->tty->flags);
if (port->count == 1)
bp->count++;
port->xmit_cnt = port->xmit_head = port->xmit_tail = 0;
sx_change_speed(bp, port);
port->flags |= ASYNC_INITIALIZED;
restore_flags(flags);
return 0;
}
/* Must be called with interrupts disabled */
static void sx_shutdown_port(struct specialix_board *bp, struct specialix_port *port)
{
struct tty_struct *tty;
if (!(port->flags & ASYNC_INITIALIZED))
return;
#ifdef SX_REPORT_OVERRUN
printk(KERN_INFO "sx%d: port %d: Total %ld overruns were detected.\n",
board_No(bp), port_No(port), port->overrun);
#endif
#ifdef SX_REPORT_FIFO
{
int i;
printk(KERN_INFO "sx%d: port %d: FIFO hits [ ",
board_No(bp), port_No(port));
for (i = 0; i < 10; i++) {
printk("%ld ", port->hits[i]);
}
printk("].\n");
}
#endif
if (port->xmit_buf) {
free_page((unsigned long) port->xmit_buf);
port->xmit_buf = NULL;
}
/* Select port */
sx_out(bp, CD186x_CAR, port_No(port));
if (!(tty = port->tty) || C_HUPCL(tty)) {
/* Drop DTR */
sx_out(bp, CD186x_MSVDTR, 0);
}
/* Reset port */
sx_wait_CCR(bp);
sx_out(bp, CD186x_CCR, CCR_SOFTRESET);
/* Disable all interrupts from this port */
port->IER = 0;
sx_out(bp, CD186x_IER, port->IER);
if (tty)
set_bit(TTY_IO_ERROR, &tty->flags);
port->flags &= ~ASYNC_INITIALIZED;
if (--bp->count < 0) {
printk(KERN_ERR "sx%d: sx_shutdown_port: bad board count: %d\n",
board_No(bp), bp->count);
bp->count = 0;
}
/*
* If this is the last opened port on the board
* shutdown whole board
*/
if (!bp->count)
sx_shutdown_board(bp);
}
static int block_til_ready(struct tty_struct *tty, struct file * filp,
struct specialix_port *port)
{
DECLARE_WAITQUEUE(wait, current);
struct specialix_board *bp = port_Board(port);
int retval;
int do_clocal = 0;
int CD;
/*
* If the device is in the middle of being closed, then block
* until it's done, and then try again.
*/
if (tty_hung_up_p(filp) || port->flags & ASYNC_CLOSING) {
interruptible_sleep_on(&port->close_wait);
if (port->flags & ASYNC_HUP_NOTIFY)
return -EAGAIN;
else
return -ERESTARTSYS;
}
/*
* If this is a callout device, then just make sure the normal
* device isn't being used.
*/
if (tty->driver.subtype == SPECIALIX_TYPE_CALLOUT) {
if (port->flags & ASYNC_NORMAL_ACTIVE)
return -EBUSY;
if ((port->flags & ASYNC_CALLOUT_ACTIVE) &&
(port->flags & ASYNC_SESSION_LOCKOUT) &&
(port->session != current->session))
return -EBUSY;
if ((port->flags & ASYNC_CALLOUT_ACTIVE) &&
(port->flags & ASYNC_PGRP_LOCKOUT) &&
(port->pgrp != current->pgrp))
return -EBUSY;
port->flags |= ASYNC_CALLOUT_ACTIVE;
return 0;
}
/*
* If non-blocking mode is set, or the port is not enabled,
* then make the check up front and then exit.
*/
if ((filp->f_flags & O_NONBLOCK) ||
(tty->flags & (1 << TTY_IO_ERROR))) {
if (port->flags & ASYNC_CALLOUT_ACTIVE)
return -EBUSY;
port->flags |= ASYNC_NORMAL_ACTIVE;
return 0;
}
if (port->flags & ASYNC_CALLOUT_ACTIVE) {
if (port->normal_termios.c_cflag & CLOCAL)
do_clocal = 1;
} else {
if (C_CLOCAL(tty))
do_clocal = 1;
}
/*
* Block waiting for the carrier detect and the line to become
* free (i.e., not in use by the callout). While we are in
* this loop, info->count is dropped by one, so that
* rs_close() knows when to free things. We restore it upon
* exit, either normal or abnormal.
*/
retval = 0;
add_wait_queue(&port->open_wait, &wait);
cli();
if (!tty_hung_up_p(filp))
port->count--;
sti();
port->blocked_open++;
while (1) {
cli();
sx_out(bp, CD186x_CAR, port_No(port));
CD = sx_in(bp, CD186x_MSVR) & MSVR_CD;
if (!(port->flags & ASYNC_CALLOUT_ACTIVE)) {
if (SX_CRTSCTS (tty)) {
/* Activate RTS */
port->MSVR |= MSVR_DTR;
sx_out (bp, CD186x_MSVR, port->MSVR);
} else {
/* Activate DTR */
port->MSVR |= MSVR_DTR;
sx_out (bp, CD186x_MSVR, port->MSVR);
}
}
sti();
set_current_state(TASK_INTERRUPTIBLE);
if (tty_hung_up_p(filp) ||
!(port->flags & ASYNC_INITIALIZED)) {
if (port->flags & ASYNC_HUP_NOTIFY)
retval = -EAGAIN;
else
retval = -ERESTARTSYS;
break;
}
if (!(port->flags & ASYNC_CALLOUT_ACTIVE) &&
!(port->flags & ASYNC_CLOSING) &&
(do_clocal || CD))
break;
if (signal_pending(current)) {
retval = -ERESTARTSYS;
break;
}
schedule();
}
current->state = TASK_RUNNING;
remove_wait_queue(&port->open_wait, &wait);
if (!tty_hung_up_p(filp))
port->count++;
port->blocked_open--;
if (retval)
return retval;
port->flags |= ASYNC_NORMAL_ACTIVE;
return 0;
}
static int sx_open(struct tty_struct * tty, struct file * filp)
{
int board;
int error;
struct specialix_port * port;
struct specialix_board * bp;
unsigned long flags;
board = SX_BOARD(MINOR(tty->device));
if (board > SX_NBOARD || !(sx_board[board].flags & SX_BOARD_PRESENT))
return -ENODEV;
bp = &sx_board[board];
port = sx_port + board * SX_NPORT + SX_PORT(MINOR(tty->device));
#ifdef DEBUG_SPECIALIX
printk (KERN_DEBUG "Board = %d, bp = %p, port = %p, portno = %d.\n",
board, bp, port, SX_PORT(MINOR(tty->device)));
#endif
if (sx_paranoia_check(port, tty->device, "sx_open"))
return -ENODEV;
if ((error = sx_setup_board(bp)))
return error;
port->count++;
tty->driver_data = port;
port->tty = tty;
if ((error = sx_setup_port(bp, port)))
return error;
if ((error = block_til_ready(tty, filp, port)))
return error;
if ((port->count == 1) && (port->flags & ASYNC_SPLIT_TERMIOS)) {
if (tty->driver.subtype == SPECIALIX_TYPE_NORMAL)
*tty->termios = port->normal_termios;
else
*tty->termios = port->callout_termios;
save_flags(flags); cli();
sx_change_speed(bp, port);
restore_flags(flags);
}
port->session = current->session;
port->pgrp = current->pgrp;
return 0;
}
static void sx_close(struct tty_struct * tty, struct file * filp)
{
struct specialix_port *port = (struct specialix_port *) tty->driver_data;
struct specialix_board *bp;
unsigned long flags;
unsigned long timeout;
if (!port || sx_paranoia_check(port, tty->device, "close"))
return;
save_flags(flags); cli();
if (tty_hung_up_p(filp)) {
restore_flags(flags);
return;
}
bp = port_Board(port);
if ((tty->count == 1) && (port->count != 1)) {
printk(KERN_ERR "sx%d: sx_close: bad port count;"
" tty->count is 1, port count is %d\n",
board_No(bp), port->count);
port->count = 1;
}
if (--port->count < 0) {
printk(KERN_ERR "sx%d: sx_close: bad port count for tty%d: %d\n",
board_No(bp), port_No(port), port->count);
port->count = 0;
}
if (port->count) {
restore_flags(flags);
return;
}
port->flags |= ASYNC_CLOSING;
/*
* Save the termios structure, since this port may have
* separate termios for callout and dialin.
*/
if (port->flags & ASYNC_NORMAL_ACTIVE)
port->normal_termios = *tty->termios;
if (port->flags & ASYNC_CALLOUT_ACTIVE)
port->callout_termios = *tty->termios;
/*
* Now we wait for the transmit buffer to clear; and we notify
* the line discipline to only process XON/XOFF characters.
*/
tty->closing = 1;
if (port->closing_wait != ASYNC_CLOSING_WAIT_NONE)
tty_wait_until_sent(tty, port->closing_wait);
/*
* At this point we stop accepting input. To do this, we
* disable the receive line status interrupts, and tell the
* interrupt driver to stop checking the data ready bit in the
* line status register.
*/
port->IER &= ~IER_RXD;
if (port->flags & ASYNC_INITIALIZED) {
port->IER &= ~IER_TXRDY;
port->IER |= IER_TXEMPTY;
sx_out(bp, CD186x_CAR, port_No(port));
sx_out(bp, CD186x_IER, port->IER);
/*
* Before we drop DTR, make sure the UART transmitter
* has completely drained; this is especially
* important if there is a transmit FIFO!
*/
timeout = jiffies+HZ;
while(port->IER & IER_TXEMPTY) {
current->state = TASK_INTERRUPTIBLE;
schedule_timeout(port->timeout);
if (time_after(jiffies, timeout)) {
printk (KERN_INFO "Timeout waiting for close\n");
break;
}
}
}
sx_shutdown_port(bp, port);
if (tty->driver.flush_buffer)
tty->driver.flush_buffer(tty);
if (tty->ldisc.flush_buffer)
tty->ldisc.flush_buffer(tty);
tty->closing = 0;
port->event = 0;
port->tty = 0;
if (port->blocked_open) {
if (port->close_delay) {
current->state = TASK_INTERRUPTIBLE;
schedule_timeout(port->close_delay);
}
wake_up_interruptible(&port->open_wait);
}
port->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CALLOUT_ACTIVE|
ASYNC_CLOSING);
wake_up_interruptible(&port->close_wait);
restore_flags(flags);
}
static int sx_write(struct tty_struct * tty, int from_user,
const unsigned char *buf, int count)
{
struct specialix_port *port = (struct specialix_port *)tty->driver_data;
struct specialix_board *bp;
int c, total = 0;
unsigned long flags;
if (sx_paranoia_check(port, tty->device, "sx_write"))
return 0;
bp = port_Board(port);
if (!tty || !port->xmit_buf || !tmp_buf)
return 0;
save_flags(flags);
if (from_user) {
down(&tmp_buf_sem);
while (1) {
c = MIN(count, MIN(SERIAL_XMIT_SIZE - port->xmit_cnt - 1,
SERIAL_XMIT_SIZE - port->xmit_head));
if (c <= 0)
break;
c -= copy_from_user(tmp_buf, buf, c);
if (!c) {
if (!total)
total = -EFAULT;
break;
}
cli();
c = MIN(c, MIN(SERIAL_XMIT_SIZE - port->xmit_cnt - 1,
SERIAL_XMIT_SIZE - port->xmit_head));
memcpy(port->xmit_buf + port->xmit_head, tmp_buf, c);
port->xmit_head = (port->xmit_head + c) & (SERIAL_XMIT_SIZE-1);
port->xmit_cnt += c;
restore_flags(flags);
buf += c;
count -= c;
total += c;
}
up(&tmp_buf_sem);
} else {
while (1) {
cli();
c = MIN(count, MIN(SERIAL_XMIT_SIZE - port->xmit_cnt - 1,
SERIAL_XMIT_SIZE - port->xmit_head));
if (c <= 0) {
restore_flags(flags);
break;
}
memcpy(port->xmit_buf + port->xmit_head, buf, c);
port->xmit_head = (port->xmit_head + c) & (SERIAL_XMIT_SIZE-1);
port->xmit_cnt += c;
restore_flags(flags);
buf += c;
count -= c;
total += c;
}
}
cli();
if (port->xmit_cnt && !tty->stopped && !tty->hw_stopped &&
!(port->IER & IER_TXRDY)) {
port->IER |= IER_TXRDY;
sx_out(bp, CD186x_CAR, port_No(port));
sx_out(bp, CD186x_IER, port->IER);
}
restore_flags(flags);
return total;
}
static void sx_put_char(struct tty_struct * tty, unsigned char ch)
{
struct specialix_port *port = (struct specialix_port *)tty->driver_data;
unsigned long flags;
if (sx_paranoia_check(port, tty->device, "sx_put_char"))
return;
if (!tty || !port->xmit_buf)
return;
save_flags(flags); cli();
if (port->xmit_cnt >= SERIAL_XMIT_SIZE - 1) {
restore_flags(flags);
return;
}
port->xmit_buf[port->xmit_head++] = ch;
port->xmit_head &= SERIAL_XMIT_SIZE - 1;
port->xmit_cnt++;
restore_flags(flags);
}
static void sx_flush_chars(struct tty_struct * tty)
{
struct specialix_port *port = (struct specialix_port *)tty->driver_data;
unsigned long flags;
if (sx_paranoia_check(port, tty->device, "sx_flush_chars"))
return;
if (port->xmit_cnt <= 0 || tty->stopped || tty->hw_stopped ||
!port->xmit_buf)
return;
save_flags(flags); cli();
port->IER |= IER_TXRDY;
sx_out(port_Board(port), CD186x_CAR, port_No(port));
sx_out(port_Board(port), CD186x_IER, port->IER);
restore_flags(flags);
}
static int sx_write_room(struct tty_struct * tty)
{
struct specialix_port *port = (struct specialix_port *)tty->driver_data;
int ret;
if (sx_paranoia_check(port, tty->device, "sx_write_room"))
return 0;
ret = SERIAL_XMIT_SIZE - port->xmit_cnt - 1;
if (ret < 0)
ret = 0;
return ret;
}
static int sx_chars_in_buffer(struct tty_struct *tty)
{
struct specialix_port *port = (struct specialix_port *)tty->driver_data;
if (sx_paranoia_check(port, tty->device, "sx_chars_in_buffer"))
return 0;
return port->xmit_cnt;
}
static void sx_flush_buffer(struct tty_struct *tty)
{
struct specialix_port *port = (struct specialix_port *)tty->driver_data;
unsigned long flags;
if (sx_paranoia_check(port, tty->device, "sx_flush_buffer"))
return;
save_flags(flags); cli();
port->xmit_cnt = port->xmit_head = port->xmit_tail = 0;
restore_flags(flags);
wake_up_interruptible(&tty->write_wait);
if ((tty->flags & (1 << TTY_DO_WRITE_WAKEUP)) &&
tty->ldisc.write_wakeup)
(tty->ldisc.write_wakeup)(tty);
}
static int sx_get_modem_info(struct specialix_port * port, unsigned int *value)
{
struct specialix_board * bp;
unsigned char status;
unsigned int result;
unsigned long flags;
bp = port_Board(port);
save_flags(flags); cli();
sx_out(bp, CD186x_CAR, port_No(port));
status = sx_in(bp, CD186x_MSVR);
restore_flags(flags);
#ifdef DEBUG_SPECIALIX
printk (KERN_DEBUG "Got msvr[%d] = %02x, car = %d.\n",
port_No(port), status, sx_in (bp, CD186x_CAR));
printk (KERN_DEBUG "sx_port = %p, port = %p\n", sx_port, port);
#endif
if (SX_CRTSCTS(port->tty)) {
result = /* (status & MSVR_RTS) ? */ TIOCM_DTR /* : 0) */
| ((status & MSVR_DTR) ? TIOCM_RTS : 0)
| ((status & MSVR_CD) ? TIOCM_CAR : 0)
|/* ((status & MSVR_DSR) ? */ TIOCM_DSR /* : 0) */
| ((status & MSVR_CTS) ? TIOCM_CTS : 0);
} else {
result = /* (status & MSVR_RTS) ? */ TIOCM_RTS /* : 0) */
| ((status & MSVR_DTR) ? TIOCM_DTR : 0)
| ((status & MSVR_CD) ? TIOCM_CAR : 0)
|/* ((status & MSVR_DSR) ? */ TIOCM_DSR /* : 0) */
| ((status & MSVR_CTS) ? TIOCM_CTS : 0);
}
put_user(result,(unsigned int *) value);
return 0;
}
static int sx_set_modem_info(struct specialix_port * port, unsigned int cmd,
unsigned int *value)
{
int error;
unsigned int arg;
unsigned long flags;
struct specialix_board *bp = port_Board(port);
error = verify_area(VERIFY_READ, value, sizeof(int));
if (error)
return error;
Get_user(arg, (unsigned long *) value);
switch (cmd) {
case TIOCMBIS:
/* if (arg & TIOCM_RTS)
port->MSVR |= MSVR_RTS; */
/* if (arg & TIOCM_DTR)
port->MSVR |= MSVR_DTR; */
if (SX_CRTSCTS(port->tty)) {
if (arg & TIOCM_RTS)
port->MSVR |= MSVR_DTR;
} else {
if (arg & TIOCM_DTR)
port->MSVR |= MSVR_DTR;
}
break;
case TIOCMBIC:
/* if (arg & TIOCM_RTS)
port->MSVR &= ~MSVR_RTS; */
/* if (arg & TIOCM_DTR)
port->MSVR &= ~MSVR_DTR; */
if (SX_CRTSCTS(port->tty)) {
if (arg & TIOCM_RTS)
port->MSVR &= ~MSVR_DTR;
} else {
if (arg & TIOCM_DTR)
port->MSVR &= ~MSVR_DTR;
}
break;
case TIOCMSET:
/* port->MSVR = (arg & TIOCM_RTS) ? (port->MSVR | MSVR_RTS) :
(port->MSVR & ~MSVR_RTS); */
/* port->MSVR = (arg & TIOCM_DTR) ? (port->MSVR | MSVR_DTR) :
(port->MSVR & ~MSVR_DTR); */
if (SX_CRTSCTS(port->tty)) {
port->MSVR = (arg & TIOCM_RTS) ?
(port->MSVR | MSVR_DTR) :
(port->MSVR & ~MSVR_DTR);
} else {
port->MSVR = (arg & TIOCM_DTR) ?
(port->MSVR | MSVR_DTR):
(port->MSVR & ~MSVR_DTR);
}
break;
default:
return -EINVAL;
}
save_flags(flags); cli();
sx_out(bp, CD186x_CAR, port_No(port));
sx_out(bp, CD186x_MSVR, port->MSVR);
restore_flags(flags);
return 0;
}
extern inline void sx_send_break(struct specialix_port * port, unsigned long length)
{
struct specialix_board *bp = port_Board(port);
unsigned long flags;
save_flags(flags); cli();
port->break_length = SPECIALIX_TPS / HZ * length;
port->COR2 |= COR2_ETC;
port->IER |= IER_TXRDY;
sx_out(bp, CD186x_CAR, port_No(port));
sx_out(bp, CD186x_COR2, port->COR2);
sx_out(bp, CD186x_IER, port->IER);
sx_wait_CCR(bp);
sx_out(bp, CD186x_CCR, CCR_CORCHG2);
sx_wait_CCR(bp);
restore_flags(flags);
}
extern inline int sx_set_serial_info(struct specialix_port * port,
struct serial_struct * newinfo)
{
struct serial_struct tmp;
struct specialix_board *bp = port_Board(port);
int change_speed;
unsigned long flags;
int error;
error = verify_area(VERIFY_READ, (void *) newinfo, sizeof(tmp));
if (error)
return error;
if (copy_from_user(&tmp, newinfo, sizeof(tmp)))
return -EFAULT;
#if 0
if ((tmp.irq != bp->irq) ||
(tmp.port != bp->base) ||
(tmp.type != PORT_CIRRUS) ||
(tmp.baud_base != (SX_OSCFREQ + CD186x_TPC/2) / CD186x_TPC) ||
(tmp.custom_divisor != 0) ||
(tmp.xmit_fifo_size != CD186x_NFIFO) ||
(tmp.flags & ~SPECIALIX_LEGAL_FLAGS))
return -EINVAL;
#endif
change_speed = ((port->flags & ASYNC_SPD_MASK) !=
(tmp.flags & ASYNC_SPD_MASK));
change_speed |= (tmp.custom_divisor != port->custom_divisor);
if (!capable(CAP_SYS_ADMIN)) {
if ((tmp.close_delay != port->close_delay) ||
(tmp.closing_wait != port->closing_wait) ||
((tmp.flags & ~ASYNC_USR_MASK) !=
(port->flags & ~ASYNC_USR_MASK)))
return -EPERM;
port->flags = ((port->flags & ~ASYNC_USR_MASK) |
(tmp.flags & ASYNC_USR_MASK));
port->custom_divisor = tmp.custom_divisor;
} else {
port->flags = ((port->flags & ~ASYNC_FLAGS) |
(tmp.flags & ASYNC_FLAGS));
port->close_delay = tmp.close_delay;
port->closing_wait = tmp.closing_wait;
port->custom_divisor = tmp.custom_divisor;
}
if (change_speed) {
save_flags(flags); cli();
sx_change_speed(bp, port);
restore_flags(flags);
}
return 0;
}
extern inline int sx_get_serial_info(struct specialix_port * port,
struct serial_struct * retinfo)
{
struct serial_struct tmp;
struct specialix_board *bp = port_Board(port);
int error;
error = verify_area(VERIFY_WRITE, (void *) retinfo, sizeof(tmp));
if (error)
return error;
memset(&tmp, 0, sizeof(tmp));
tmp.type = PORT_CIRRUS;
tmp.line = port - sx_port;
tmp.port = bp->base;
tmp.irq = bp->irq;
tmp.flags = port->flags;
tmp.baud_base = (SX_OSCFREQ + CD186x_TPC/2) / CD186x_TPC;
tmp.close_delay = port->close_delay * HZ/100;
tmp.closing_wait = port->closing_wait * HZ/100;
tmp.custom_divisor = port->custom_divisor;
tmp.xmit_fifo_size = CD186x_NFIFO;
if (copy_to_user(retinfo, &tmp, sizeof(tmp)))
return -EFAULT;
return 0;
}
static int sx_ioctl(struct tty_struct * tty, struct file * filp,
unsigned int cmd, unsigned long arg)
{
struct specialix_port *port = (struct specialix_port *)tty->driver_data;
int error;
int retval;
if (sx_paranoia_check(port, tty->device, "sx_ioctl"))
return -ENODEV;
switch (cmd) {
case TCSBRK: /* SVID version: non-zero arg --> no break */
retval = tty_check_change(tty);
if (retval)
return retval;
tty_wait_until_sent(tty, 0);
if (!arg)
sx_send_break(port, HZ/4); /* 1/4 second */
return 0;
case TCSBRKP: /* support for POSIX tcsendbreak() */
retval = tty_check_change(tty);
if (retval)
return retval;
tty_wait_until_sent(tty, 0);
sx_send_break(port, arg ? arg*(HZ/10) : HZ/4);
return 0;
case TIOCGSOFTCAR:
error = verify_area(VERIFY_WRITE, (void *) arg, sizeof(long));
if (error)
return error;
put_user(C_CLOCAL(tty) ? 1 : 0,
(unsigned long *) arg);
return 0;
case TIOCSSOFTCAR:
Get_user(arg, (unsigned long *) arg);
tty->termios->c_cflag =
((tty->termios->c_cflag & ~CLOCAL) |
(arg ? CLOCAL : 0));
return 0;
case TIOCMGET:
error = verify_area(VERIFY_WRITE, (void *) arg,
sizeof(unsigned int));
if (error)
return error;
return sx_get_modem_info(port, (unsigned int *) arg);
case TIOCMBIS:
case TIOCMBIC:
case TIOCMSET:
return sx_set_modem_info(port, cmd, (unsigned int *) arg);
case TIOCGSERIAL:
return sx_get_serial_info(port, (struct serial_struct *) arg);
case TIOCSSERIAL:
return sx_set_serial_info(port, (struct serial_struct *) arg);
default:
return -ENOIOCTLCMD;
}
return 0;
}
static void sx_throttle(struct tty_struct * tty)
{
struct specialix_port *port = (struct specialix_port *)tty->driver_data;
struct specialix_board *bp;
unsigned long flags;
if (sx_paranoia_check(port, tty->device, "sx_throttle"))
return;
bp = port_Board(port);
save_flags(flags); cli();
/* Use DTR instead of RTS ! */
if (SX_CRTSCTS (tty))
port->MSVR &= ~MSVR_DTR;
else {
/* Auch!!! I think the system shouldn't call this then. */
/* Or maybe we're supposed (allowed?) to do our side of hw
handshake anyway, even when hardware handshake is off.
When you see this in your logs, please report.... */
printk (KERN_ERR "sx%d: Need to throttle, but can't (hardware hs is off)\n",
port_No (port));
}
sx_out(bp, CD186x_CAR, port_No(port));
if (I_IXOFF(tty)) {
sx_wait_CCR(bp);
sx_out(bp, CD186x_CCR, CCR_SSCH2);
sx_wait_CCR(bp);
}
sx_out(bp, CD186x_MSVR, port->MSVR);
restore_flags(flags);
}
static void sx_unthrottle(struct tty_struct * tty)
{
struct specialix_port *port = (struct specialix_port *)tty->driver_data;
struct specialix_board *bp;
unsigned long flags;
if (sx_paranoia_check(port, tty->device, "sx_unthrottle"))
return;
bp = port_Board(port);
save_flags(flags); cli();
/* XXXX Use DTR INSTEAD???? */
if (SX_CRTSCTS(tty)) {
port->MSVR |= MSVR_DTR;
} /* Else clause: see remark in "sx_throttle"... */
sx_out(bp, CD186x_CAR, port_No(port));
if (I_IXOFF(tty)) {
sx_wait_CCR(bp);
sx_out(bp, CD186x_CCR, CCR_SSCH1);
sx_wait_CCR(bp);
}
sx_out(bp, CD186x_MSVR, port->MSVR);
restore_flags(flags);
}
static void sx_stop(struct tty_struct * tty)
{
struct specialix_port *port = (struct specialix_port *)tty->driver_data;
struct specialix_board *bp;
unsigned long flags;
if (sx_paranoia_check(port, tty->device, "sx_stop"))
return;
bp = port_Board(port);
save_flags(flags); cli();
port->IER &= ~IER_TXRDY;
sx_out(bp, CD186x_CAR, port_No(port));
sx_out(bp, CD186x_IER, port->IER);
restore_flags(flags);
}
static void sx_start(struct tty_struct * tty)
{
struct specialix_port *port = (struct specialix_port *)tty->driver_data;
struct specialix_board *bp;
unsigned long flags;
if (sx_paranoia_check(port, tty->device, "sx_start"))
return;
bp = port_Board(port);
save_flags(flags); cli();
if (port->xmit_cnt && port->xmit_buf && !(port->IER & IER_TXRDY)) {
port->IER |= IER_TXRDY;
sx_out(bp, CD186x_CAR, port_No(port));
sx_out(bp, CD186x_IER, port->IER);
}
restore_flags(flags);
}
/*
* This routine is called from the scheduler tqueue when the interrupt
* routine has signalled that a hangup has occurred. The path of
* hangup processing is:
*
* serial interrupt routine -> (scheduler tqueue) ->
* do_sx_hangup() -> tty->hangup() -> sx_hangup()
*
*/
static void do_sx_hangup(void *private_)
{
struct specialix_port *port = (struct specialix_port *) private_;
struct tty_struct *tty;
tty = port->tty;
if (tty)
tty_hangup(tty); /* FIXME: module removal race here */
MOD_DEC_USE_COUNT;
}
static void sx_hangup(struct tty_struct * tty)
{
struct specialix_port *port = (struct specialix_port *)tty->driver_data;
struct specialix_board *bp;
if (sx_paranoia_check(port, tty->device, "sx_hangup"))
return;
bp = port_Board(port);
sx_shutdown_port(bp, port);
port->event = 0;
port->count = 0;
port->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CALLOUT_ACTIVE);
port->tty = 0;
wake_up_interruptible(&port->open_wait);
}
static void sx_set_termios(struct tty_struct * tty, struct termios * old_termios)
{
struct specialix_port *port = (struct specialix_port *)tty->driver_data;
unsigned long flags;
if (sx_paranoia_check(port, tty->device, "sx_set_termios"))
return;
if (tty->termios->c_cflag == old_termios->c_cflag &&
tty->termios->c_iflag == old_termios->c_iflag)
return;
save_flags(flags); cli();
sx_change_speed(port_Board(port), port);
restore_flags(flags);
if ((old_termios->c_cflag & CRTSCTS) &&
!(tty->termios->c_cflag & CRTSCTS)) {
tty->hw_stopped = 0;
sx_start(tty);
}
}
static void do_specialix_bh(void)
{
run_task_queue(&tq_specialix);
}
static void do_softint(void *private_)
{
struct specialix_port *port = (struct specialix_port *) private_;
struct tty_struct *tty;
if(!(tty = port->tty))
return;
if (test_and_clear_bit(RS_EVENT_WRITE_WAKEUP, &port->event)) {
if ((tty->flags & (1 << TTY_DO_WRITE_WAKEUP)) &&
tty->ldisc.write_wakeup)
(tty->ldisc.write_wakeup)(tty);
wake_up_interruptible(&tty->write_wait);
}
}
static int sx_init_drivers(void)
{
int error;
int i;
if (!(tmp_buf = (unsigned char *) get_free_page(GFP_KERNEL))) {
printk(KERN_ERR "sx: Couldn't get free page.\n");
return 1;
}
init_bh(SPECIALIX_BH, do_specialix_bh);
memset(&specialix_driver, 0, sizeof(specialix_driver));
specialix_driver.magic = TTY_DRIVER_MAGIC;
specialix_driver.name = "ttyW";
specialix_driver.major = SPECIALIX_NORMAL_MAJOR;
specialix_driver.num = SX_NBOARD * SX_NPORT;
specialix_driver.type = TTY_DRIVER_TYPE_SERIAL;
specialix_driver.subtype = SPECIALIX_TYPE_NORMAL;
specialix_driver.init_termios = tty_std_termios;
specialix_driver.init_termios.c_cflag =
B9600 | CS8 | CREAD | HUPCL | CLOCAL;
specialix_driver.flags = TTY_DRIVER_REAL_RAW;
specialix_driver.refcount = &specialix_refcount;
specialix_driver.table = specialix_table;
specialix_driver.termios = specialix_termios;
specialix_driver.termios_locked = specialix_termios_locked;
specialix_driver.open = sx_open;
specialix_driver.close = sx_close;
specialix_driver.write = sx_write;
specialix_driver.put_char = sx_put_char;
specialix_driver.flush_chars = sx_flush_chars;
specialix_driver.write_room = sx_write_room;
specialix_driver.chars_in_buffer = sx_chars_in_buffer;
specialix_driver.flush_buffer = sx_flush_buffer;
specialix_driver.ioctl = sx_ioctl;
specialix_driver.throttle = sx_throttle;
specialix_driver.unthrottle = sx_unthrottle;
specialix_driver.set_termios = sx_set_termios;
specialix_driver.stop = sx_stop;
specialix_driver.start = sx_start;
specialix_driver.hangup = sx_hangup;
specialix_callout_driver = specialix_driver;
specialix_callout_driver.name = "cuw";
specialix_callout_driver.major = SPECIALIX_CALLOUT_MAJOR;
specialix_callout_driver.subtype = SPECIALIX_TYPE_CALLOUT;
if ((error = tty_register_driver(&specialix_driver))) {
free_page((unsigned long)tmp_buf);
printk(KERN_ERR "sx: Couldn't register specialix IO8+ driver, error = %d\n",
error);
return 1;
}
if ((error = tty_register_driver(&specialix_callout_driver))) {
free_page((unsigned long)tmp_buf);
tty_unregister_driver(&specialix_driver);
printk(KERN_ERR "sx: Couldn't register specialix IO8+ callout driver, error = %d\n",
error);
return 1;
}
memset(sx_port, 0, sizeof(sx_port));
for (i = 0; i < SX_NPORT * SX_NBOARD; i++) {
sx_port[i].callout_termios = specialix_callout_driver.init_termios;
sx_port[i].normal_termios = specialix_driver.init_termios;
sx_port[i].magic = SPECIALIX_MAGIC;
sx_port[i].tqueue.routine = do_softint;
sx_port[i].tqueue.data = &sx_port[i];
sx_port[i].tqueue_hangup.routine = do_sx_hangup;
sx_port[i].tqueue_hangup.data = &sx_port[i];
sx_port[i].close_delay = 50 * HZ/100;
sx_port[i].closing_wait = 3000 * HZ/100;
init_waitqueue_head(&sx_port[i].open_wait);
init_waitqueue_head(&sx_port[i].close_wait);
}
return 0;
}
static void sx_release_drivers(void)
{
free_page((unsigned long)tmp_buf);
tty_unregister_driver(&specialix_driver);
tty_unregister_driver(&specialix_callout_driver);
}
#ifndef MODULE
/*
* Called at boot time.
*
* You can specify IO base for up to SX_NBOARD cards,
* using line "specialix=0xiobase1,0xiobase2,.." at LILO prompt.
* Note that there will be no probing at default
* addresses in this case.
*
*/
void specialix_setup(char *str, int * ints)
{
int i;
for (i=0;i<SX_NBOARD;i++) {
sx_board[i].base = 0;
}
for (i = 1; i <= ints[0]; i++) {
if (i&1)
sx_board[i/2].base = ints[i];
else
sx_board[i/2 -1].irq = ints[i];
}
}
#endif
/*
* This routine must be called by kernel at boot time
*/
int specialix_init(void)
{
int i;
int found = 0;
printk(KERN_INFO "sx: Specialix IO8+ driver v" VERSION ", (c) R.E.Wolff 1997/1998.\n");
printk(KERN_INFO "sx: derived from work (c) D.Gorodchanin 1994-1996.\n");
#ifdef CONFIG_SPECIALIX_RTSCTS
printk (KERN_INFO "sx: DTR/RTS pin is always RTS.\n");
#else
printk (KERN_INFO "sx: DTR/RTS pin is RTS when CRTSCTS is on.\n");
#endif
if (sx_init_drivers())
return -EIO;
for (i = 0; i < SX_NBOARD; i++)
if (sx_board[i].base && !sx_probe(&sx_board[i]))
found++;
#ifdef CONFIG_PCI
if (pci_present()) {
struct pci_dev *pdev = NULL;
i=0;
while (i <= SX_NBOARD) {
if (sx_board[i].flags & SX_BOARD_PRESENT) {
i++;
continue;
}
pdev = pci_find_device (PCI_VENDOR_ID_SPECIALIX,
PCI_DEVICE_ID_SPECIALIX_IO8,
pdev);
if (!pdev) break;
if (pci_enable_device(pdev))
continue;
sx_board[i].irq = pdev->irq;
sx_board[i].base = pci_resource_start (pdev, 2);
sx_board[i].flags |= SX_BOARD_IS_PCI;
if (!sx_probe(&sx_board[i]))
found ++;
}
}
#endif
if (!found) {
sx_release_drivers();
printk(KERN_INFO "sx: No specialix IO8+ boards detected.\n");
return -EIO;
}
return 0;
}
#ifdef MODULE
int iobase[SX_NBOARD] = {0,};
int irq [SX_NBOARD] = {0,};
MODULE_PARM(iobase,"1-" __MODULE_STRING(SX_NBOARD) "i");
MODULE_PARM(irq,"1-" __MODULE_STRING(SX_NBOARD) "i");
/*
* You can setup up to 4 boards.
* by specifying "iobase=0xXXX,0xXXX ..." as insmod parameter.
* You should specify the IRQs too in that case "irq=....,...".
*
* More than 4 boards in one computer is not possible, as the card can
* only use 4 different interrupts.
*
*/
int init_module(void)
{
int i;
if (iobase[0] || iobase[1] || iobase[2] || iobase[3]) {
for(i = 0; i < SX_NBOARD; i++) {
sx_board[i].base = iobase[i];
sx_board[i].irq = irq[i];
}
}
return specialix_init();
}
void cleanup_module(void)
{
int i;
sx_release_drivers();
for (i = 0; i < SX_NBOARD; i++)
if (sx_board[i].flags & SX_BOARD_PRESENT)
sx_release_io_range(&sx_board[i]);
#ifdef SPECIALIX_TIMER
del_timer (&missed_irq_timer);
#endif
}
#endif /* MODULE */
MODULE_LICENSE("GPL");
|