Viewing file:  rioboard.h (13.23 KB) -rw-r--r--
Select action/file-type:
 (+) |  (+) |  (+) | Code (+) | Session (+) |  (+) | SDB (+) |  (+) |  (+) |  (+) |  (+) |  (+) |
/************************************************************************/
/* */
/* Title : RIO Host Card Hardware Definitions */
/* */
/* Author : N.P.Vassallo */
/* */
/* Creation : 26th April 1999 */
/* */
/* Version : 1.0.0 */
/* */
/* Copyright : (c) Specialix International Ltd. 1999 *
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
* */
/* Description : Prototypes, structures and definitions */
/* describing the RIO board hardware */
/* */
/************************************************************************/
/* History...
1.0.0 26/04/99 NPV Creation.
*/
#ifndef _rioboard_h /* If RIOBOARD.H not already defined */
#define _rioboard_h 1
/*****************************************************************************
*********************** ***********************
*********************** Hardware Control Registers ***********************
*********************** ***********************
*****************************************************************************/
/* Hardware Registers... */
#define RIO_REG_BASE 0x7C00 /* Base of control registers */
#define RIO_CONFIG RIO_REG_BASE + 0x0000 /* WRITE: Configuration Register */
#define RIO_INTSET RIO_REG_BASE + 0x0080 /* WRITE: Interrupt Set */
#define RIO_RESET RIO_REG_BASE + 0x0100 /* WRITE: Host Reset */
#define RIO_INTRESET RIO_REG_BASE + 0x0180 /* WRITE: Interrupt Reset */
#define RIO_VPD_ROM RIO_REG_BASE + 0x0000 /* READ: Vital Product Data ROM */
#define RIO_INTSTAT RIO_REG_BASE + 0x0080 /* READ: Interrupt Status (Jet boards only) */
#define RIO_RESETSTAT RIO_REG_BASE + 0x0100 /* READ: Reset Status (Jet boards only) */
/* RIO_VPD_ROM definitions... */
#define VPD_SLX_ID1 0x00 /* READ: Specialix Identifier #1 */
#define VPD_SLX_ID2 0x01 /* READ: Specialix Identifier #2 */
#define VPD_HW_REV 0x02 /* READ: Hardware Revision */
#define VPD_HW_ASSEM 0x03 /* READ: Hardware Assembly Level */
#define VPD_UNIQUEID4 0x04 /* READ: Unique Identifier #4 */
#define VPD_UNIQUEID3 0x05 /* READ: Unique Identifier #3 */
#define VPD_UNIQUEID2 0x06 /* READ: Unique Identifier #2 */
#define VPD_UNIQUEID1 0x07 /* READ: Unique Identifier #1 */
#define VPD_MANU_YEAR 0x08 /* READ: Year Of Manufacture (0 = 1970) */
#define VPD_MANU_WEEK 0x09 /* READ: Week Of Manufacture (0 = week 1 Jan) */
#define VPD_HWFEATURE1 0x0A /* READ: Hardware Feature Byte 1 */
#define VPD_HWFEATURE2 0x0B /* READ: Hardware Feature Byte 2 */
#define VPD_HWFEATURE3 0x0C /* READ: Hardware Feature Byte 3 */
#define VPD_HWFEATURE4 0x0D /* READ: Hardware Feature Byte 4 */
#define VPD_HWFEATURE5 0x0E /* READ: Hardware Feature Byte 5 */
#define VPD_OEMID 0x0F /* READ: OEM Identifier */
#define VPD_IDENT 0x10 /* READ: Identifier string (16 bytes) */
#define VPD_IDENT_LEN 0x10
/* VPD ROM Definitions... */
#define SLX_ID1 0x4D
#define SLX_ID2 0x98
#define PRODUCT_ID(a) ((a>>4)&0xF) /* Use to obtain Product ID from VPD_UNIQUEID1 */
#define ID_SX_ISA 0x2
#define ID_RIO_EISA 0x3
#define ID_SX_PCI 0x5
#define ID_SX_EISA 0x7
#define ID_RIO_RTA16 0x9
#define ID_RIO_ISA 0xA
#define ID_RIO_MCA 0xB
#define ID_RIO_SBUS 0xC
#define ID_RIO_PCI 0xD
#define ID_RIO_RTA8 0xE
/* Transputer bootstrap definitions... */
#define BOOTLOADADDR (0x8000 - 6)
#define BOOTINDICATE (0x8000 - 2)
/* Firmware load position... */
#define FIRMWARELOADADDR 0x7C00 /* Firmware is loaded _before_ this address */
/*****************************************************************************
***************************** *****************************
***************************** RIO (Rev1) ISA *****************************
***************************** *****************************
*****************************************************************************/
/* Control Register Definitions... */
#define RIO_ISA_IDENT "JBJGPGGHINSMJPJR"
#define RIO_ISA_CFG_BOOTRAM 0x01 /* Boot from RAM, else Link */
#define RIO_ISA_CFG_BUSENABLE 0x02 /* Enable processor bus */
#define RIO_ISA_CFG_IRQMASK 0x30 /* Interrupt mask */
#define RIO_ISA_CFG_IRQ12 0x10 /* Interrupt Level 12 */
#define RIO_ISA_CFG_IRQ11 0x20 /* Interrupt Level 11 */
#define RIO_ISA_CFG_IRQ9 0x30 /* Interrupt Level 9 */
#define RIO_ISA_CFG_LINK20 0x40 /* 20Mbps link, else 10Mbps */
#define RIO_ISA_CFG_WAITSTATE0 0x80 /* 0 waitstates, else 1 */
/*****************************************************************************
***************************** *****************************
***************************** RIO (Rev2) ISA *****************************
***************************** *****************************
*****************************************************************************/
/* Control Register Definitions... */
#define RIO_ISA2_IDENT "JBJGPGGHINSMJPJR"
#define RIO_ISA2_CFG_BOOTRAM 0x01 /* Boot from RAM, else Link */
#define RIO_ISA2_CFG_BUSENABLE 0x02 /* Enable processor bus */
#define RIO_ISA2_CFG_INTENABLE 0x04 /* Interrupt enable, else disable */
#define RIO_ISA2_CFG_16BIT 0x08 /* 16bit mode, else 8bit */
#define RIO_ISA2_CFG_IRQMASK 0x30 /* Interrupt mask */
#define RIO_ISA2_CFG_IRQ15 0x00 /* Interrupt Level 15 */
#define RIO_ISA2_CFG_IRQ12 0x10 /* Interrupt Level 12 */
#define RIO_ISA2_CFG_IRQ11 0x20 /* Interrupt Level 11 */
#define RIO_ISA2_CFG_IRQ9 0x30 /* Interrupt Level 9 */
#define RIO_ISA2_CFG_LINK20 0x40 /* 20Mbps link, else 10Mbps */
#define RIO_ISA2_CFG_WAITSTATE0 0x80 /* 0 waitstates, else 1 */
/*****************************************************************************
***************************** ******************************
***************************** RIO (Jet) ISA ******************************
***************************** ******************************
*****************************************************************************/
/* Control Register Definitions... */
#define RIO_ISA3_IDENT "JET HOST BY KEV#"
#define RIO_ISA3_CFG_BUSENABLE 0x02 /* Enable processor bus */
#define RIO_ISA3_CFG_INTENABLE 0x04 /* Interrupt enable, else disable */
#define RIO_ISA32_CFG_IRQMASK 0xF30 /* Interrupt mask */
#define RIO_ISA3_CFG_IRQ15 0xF0 /* Interrupt Level 15 */
#define RIO_ISA3_CFG_IRQ12 0xC0 /* Interrupt Level 12 */
#define RIO_ISA3_CFG_IRQ11 0xB0 /* Interrupt Level 11 */
#define RIO_ISA3_CFG_IRQ10 0xA0 /* Interrupt Level 10 */
#define RIO_ISA3_CFG_IRQ9 0x90 /* Interrupt Level 9 */
/*****************************************************************************
********************************* ********************************
********************************* RIO MCA ********************************
********************************* ********************************
*****************************************************************************/
/* Control Register Definitions... */
#define RIO_MCA_IDENT "JBJGPGGHINSMJPJR"
#define RIO_MCA_CFG_BOOTRAM 0x01 /* Boot from RAM, else Link */
#define RIO_MCA_CFG_BUSENABLE 0x02 /* Enable processor bus */
#define RIO_MCA_CFG_LINK20 0x40 /* 20Mbps link, else 10Mbps */
/*****************************************************************************
******************************** ********************************
******************************** RIO EISA ********************************
******************************** ********************************
*****************************************************************************/
/* EISA Configuration Space Definitions... */
#define EISA_PRODUCT_ID1 0xC80
#define EISA_PRODUCT_ID2 0xC81
#define EISA_PRODUCT_NUMBER 0xC82
#define EISA_REVISION_NUMBER 0xC83
#define EISA_CARD_ENABLE 0xC84
#define EISA_VPD_UNIQUEID4 0xC88 /* READ: Unique Identifier #4 */
#define EISA_VPD_UNIQUEID3 0xC8A /* READ: Unique Identifier #3 */
#define EISA_VPD_UNIQUEID2 0xC90 /* READ: Unique Identifier #2 */
#define EISA_VPD_UNIQUEID1 0xC92 /* READ: Unique Identifier #1 */
#define EISA_VPD_MANU_YEAR 0xC98 /* READ: Year Of Manufacture (0 = 1970) */
#define EISA_VPD_MANU_WEEK 0xC9A /* READ: Week Of Manufacture (0 = week 1 Jan) */
#define EISA_MEM_ADDR_23_16 0xC00
#define EISA_MEM_ADDR_31_24 0xC01
#define EISA_RIO_CONFIG 0xC02 /* WRITE: Configuration Register */
#define EISA_RIO_INTSET 0xC03 /* WRITE: Interrupt Set */
#define EISA_RIO_INTRESET 0xC03 /* READ: Interrupt Reset */
/* Control Register Definitions... */
#define RIO_EISA_CFG_BOOTRAM 0x01 /* Boot from RAM, else Link */
#define RIO_EISA_CFG_LINK20 0x02 /* 20Mbps link, else 10Mbps */
#define RIO_EISA_CFG_BUSENABLE 0x04 /* Enable processor bus */
#define RIO_EISA_CFG_PROCRUN 0x08 /* Processor running, else reset */
#define RIO_EISA_CFG_IRQMASK 0xF0 /* Interrupt mask */
#define RIO_EISA_CFG_IRQ15 0xF0 /* Interrupt Level 15 */
#define RIO_EISA_CFG_IRQ14 0xE0 /* Interrupt Level 14 */
#define RIO_EISA_CFG_IRQ12 0xC0 /* Interrupt Level 12 */
#define RIO_EISA_CFG_IRQ11 0xB0 /* Interrupt Level 11 */
#define RIO_EISA_CFG_IRQ10 0xA0 /* Interrupt Level 10 */
#define RIO_EISA_CFG_IRQ9 0x90 /* Interrupt Level 9 */
#define RIO_EISA_CFG_IRQ7 0x70 /* Interrupt Level 7 */
#define RIO_EISA_CFG_IRQ6 0x60 /* Interrupt Level 6 */
#define RIO_EISA_CFG_IRQ5 0x50 /* Interrupt Level 5 */
#define RIO_EISA_CFG_IRQ4 0x40 /* Interrupt Level 4 */
#define RIO_EISA_CFG_IRQ3 0x30 /* Interrupt Level 3 */
/*****************************************************************************
******************************** ********************************
******************************** RIO SBus ********************************
******************************** ********************************
*****************************************************************************/
/* Control Register Definitions... */
#define RIO_SBUS_IDENT "JBPGK#\0\0\0\0\0\0\0\0\0\0"
#define RIO_SBUS_CFG_BOOTRAM 0x01 /* Boot from RAM, else Link */
#define RIO_SBUS_CFG_BUSENABLE 0x02 /* Enable processor bus */
#define RIO_SBUS_CFG_INTENABLE 0x04 /* Interrupt enable, else disable */
#define RIO_SBUS_CFG_IRQMASK 0x38 /* Interrupt mask */
#define RIO_SBUS_CFG_IRQNONE 0x00 /* No Interrupt */
#define RIO_SBUS_CFG_IRQ7 0x38 /* Interrupt Level 7 */
#define RIO_SBUS_CFG_IRQ6 0x30 /* Interrupt Level 6 */
#define RIO_SBUS_CFG_IRQ5 0x28 /* Interrupt Level 5 */
#define RIO_SBUS_CFG_IRQ4 0x20 /* Interrupt Level 4 */
#define RIO_SBUS_CFG_IRQ3 0x18 /* Interrupt Level 3 */
#define RIO_SBUS_CFG_IRQ2 0x10 /* Interrupt Level 2 */
#define RIO_SBUS_CFG_IRQ1 0x08 /* Interrupt Level 1 */
#define RIO_SBUS_CFG_LINK20 0x40 /* 20Mbps link, else 10Mbps */
#define RIO_SBUS_CFG_PROC25 0x80 /* 25Mhz processor clock, else 20Mhz */
/*****************************************************************************
********************************* ********************************
********************************* RIO PCI ********************************
********************************* ********************************
*****************************************************************************/
/* Control Register Definitions... */
#define RIO_PCI_IDENT "ECDDPGJGJHJRGSK#"
#define RIO_PCI_CFG_BOOTRAM 0x01 /* Boot from RAM, else Link */
#define RIO_PCI_CFG_BUSENABLE 0x02 /* Enable processor bus */
#define RIO_PCI_CFG_INTENABLE 0x04 /* Interrupt enable, else disable */
#define RIO_PCI_CFG_LINK20 0x40 /* 20Mbps link, else 10Mbps */
#define RIO_PCI_CFG_PROC25 0x80 /* 25Mhz processor clock, else 20Mhz */
/* PCI Definitions... */
#define SPX_VENDOR_ID 0x11CB /* Assigned by the PCI SIG */
#define SPX_DEVICE_ID 0x8000 /* RIO bridge boards */
#define SPX_PLXDEVICE_ID 0x2000 /* PLX bridge boards */
#define SPX_SUB_VENDOR_ID SPX_VENDOR_ID /* Same as vendor id */
#define RIO_SUB_SYS_ID 0x0800 /* RIO PCI board */
/*****************************************************************************
***************************** ******************************
***************************** RIO (Jet) PCI ******************************
***************************** ******************************
*****************************************************************************/
/* Control Register Definitions... */
#define RIO_PCI2_IDENT "JET HOST BY KEV#"
#define RIO_PCI2_CFG_BUSENABLE 0x02 /* Enable processor bus */
#define RIO_PCI2_CFG_INTENABLE 0x04 /* Interrupt enable, else disable */
/* PCI Definitions... */
#define RIO2_SUB_SYS_ID 0x0100 /* RIO (Jet) PCI board */
#endif /*_rioboard_h */
/* End of RIOBOARD.H */
|