Viewing file:  pd.c (28.53 KB) -rw-r--r--
Select action/file-type:
 (+) |  (+) |  (+) | Code (+) | Session (+) |  (+) | SDB (+) |  (+) |  (+) |  (+) |  (+) |  (+) |
/*
pd.c (c) 1997-8 Grant R. Guenther <grant@torque.net>
Under the terms of the GNU General Public License.
This is the high-level driver for parallel port IDE hard
drives based on chips supported by the paride module.
By default, the driver will autoprobe for a single parallel
port IDE drive, but if their individual parameters are
specified, the driver can handle up to 4 drives.
The behaviour of the pd driver can be altered by setting
some parameters from the insmod command line. The following
parameters are adjustable:
drive0 These four arguments can be arrays of
drive1 1-8 integers as follows:
drive2
drive3 <prt>,<pro>,<uni>,<mod>,<geo>,<sby>,<dly>,<slv>
Where,
<prt> is the base of the parallel port address for
the corresponding drive. (required)
<pro> is the protocol number for the adapter that
supports this drive. These numbers are
logged by 'paride' when the protocol modules
are initialised. (0 if not given)
<uni> for those adapters that support chained
devices, this is the unit selector for the
chain of devices on the given port. It should
be zero for devices that don't support chaining.
(0 if not given)
<mod> this can be -1 to choose the best mode, or one
of the mode numbers supported by the adapter.
(-1 if not given)
<geo> this defaults to 0 to indicate that the driver
should use the CHS geometry provided by the drive
itself. If set to 1, the driver will provide
a logical geometry with 64 heads and 32 sectors
per track, to be consistent with most SCSI
drivers. (0 if not given)
<sby> set this to zero to disable the power saving
standby mode, if needed. (1 if not given)
<dly> some parallel ports require the driver to
go more slowly. -1 sets a default value that
should work with the chosen protocol. Otherwise,
set this to a small integer, the larger it is
the slower the port i/o. In some cases, setting
this to zero will speed up the device. (default -1)
<slv> IDE disks can be jumpered to master or slave.
Set this to 0 to choose the master drive, 1 to
choose the slave, -1 (the default) to choose the
first drive found.
major You may use this parameter to overide the
default major number (45) that this driver
will use. Be sure to change the device
name as well.
name This parameter is a character string that
contains the name the kernel will use for this
device (in /proc output, for instance).
(default "pd")
cluster The driver will attempt to aggregate requests
for adjacent blocks into larger multi-block
clusters. The maximum cluster size (in 512
byte sectors) is set with this parameter.
(default 64)
verbose This parameter controls the amount of logging
that the driver will do. Set it to 0 for
normal operation, 1 to see autoprobe progress
messages, or 2 to see additional debugging
output. (default 0)
nice This parameter controls the driver's use of
idle CPU time, at the expense of some speed.
If this driver is built into the kernel, you can use kernel
the following command line parameters, with the same values
as the corresponding module parameters listed above:
pd.drive0
pd.drive1
pd.drive2
pd.drive3
pd.cluster
pd.nice
In addition, you can use the parameter pd.disable to disable
the driver entirely.
*/
/* Changes:
1.01 GRG 1997.01.24 Restored pd_reset()
Added eject ioctl
1.02 GRG 1998.05.06 SMP spinlock changes,
Added slave support
1.03 GRG 1998.06.16 Eliminate an Ugh.
1.04 GRG 1998.08.15 Extra debugging, use HZ in loop timing
1.05 GRG 1998.09.24 Added jumbo support
*/
#define PD_VERSION "1.05"
#define PD_MAJOR 45
#define PD_NAME "pd"
#define PD_UNITS 4
/* Here are things one can override from the insmod command.
Most are autoprobed by paride unless set here. Verbose is off
by default.
*/
static int verbose = 0;
static int major = PD_MAJOR;
static char *name = PD_NAME;
static int cluster = 64;
static int nice = 0;
static int disable = 0;
static int drive0[8] = {0,0,0,-1,0,1,-1,-1};
static int drive1[8] = {0,0,0,-1,0,1,-1,-1};
static int drive2[8] = {0,0,0,-1,0,1,-1,-1};
static int drive3[8] = {0,0,0,-1,0,1,-1,-1};
static int (*drives[4])[8] = {&drive0,&drive1,&drive2,&drive3};
static int pd_drive_count;
#define D_PRT 0
#define D_PRO 1
#define D_UNI 2
#define D_MOD 3
#define D_GEO 4
#define D_SBY 5
#define D_DLY 6
#define D_SLV 7
#define DU (*drives[unit])
/* end of parameters */
#include <linux/module.h>
#include <linux/errno.h>
#include <linux/fs.h>
#include <linux/devfs_fs_kernel.h>
#include <linux/kernel.h>
#include <linux/delay.h>
#include <linux/genhd.h>
#include <linux/hdreg.h>
#include <linux/cdrom.h> /* for the eject ioctl */
#include <linux/spinlock.h>
#include <asm/uaccess.h>
#ifndef MODULE
#include "setup.h"
static STT pd_stt[7] = {{"drive0",8,drive0},
{"drive1",8,drive1},
{"drive2",8,drive2},
{"drive3",8,drive3},
{"disable",1,&disable},
{"cluster",1,&cluster},
{"nice",1,&nice}};
void pd_setup( char *str, int *ints)
{ generic_setup(pd_stt,7,str);
}
#endif
MODULE_PARM(verbose,"i");
MODULE_PARM(major,"i");
MODULE_PARM(name,"s");
MODULE_PARM(cluster,"i");
MODULE_PARM(nice,"i");
MODULE_PARM(drive0,"1-8i");
MODULE_PARM(drive1,"1-8i");
MODULE_PARM(drive2,"1-8i");
MODULE_PARM(drive3,"1-8i");
#include "paride.h"
#define PD_BITS 4
/* set up defines for blk.h, why don't all drivers do it this way ? */
#define MAJOR_NR major
#define DEVICE_NAME "PD"
#define DEVICE_REQUEST do_pd_request
#define DEVICE_NR(device) (MINOR(device)>>PD_BITS)
#define DEVICE_ON(device)
#define DEVICE_OFF(device)
#include <linux/blk.h>
#include <linux/blkpg.h>
#include "pseudo.h"
#define PD_PARTNS (1<<PD_BITS)
#define PD_DEVS PD_PARTNS*PD_UNITS
/* numbers for "SCSI" geometry */
#define PD_LOG_HEADS 64
#define PD_LOG_SECTS 32
#define PD_ID_OFF 54
#define PD_ID_LEN 14
#define PD_MAX_RETRIES 5
#define PD_TMO 800 /* interrupt timeout in jiffies */
#define PD_SPIN_DEL 50 /* spin delay in micro-seconds */
#define PD_SPIN (1000000*PD_TMO)/(HZ*PD_SPIN_DEL)
#define STAT_ERR 0x00001
#define STAT_INDEX 0x00002
#define STAT_ECC 0x00004
#define STAT_DRQ 0x00008
#define STAT_SEEK 0x00010
#define STAT_WRERR 0x00020
#define STAT_READY 0x00040
#define STAT_BUSY 0x00080
#define ERR_AMNF 0x00100
#define ERR_TK0NF 0x00200
#define ERR_ABRT 0x00400
#define ERR_MCR 0x00800
#define ERR_IDNF 0x01000
#define ERR_MC 0x02000
#define ERR_UNC 0x04000
#define ERR_TMO 0x10000
#define IDE_READ 0x20
#define IDE_WRITE 0x30
#define IDE_READ_VRFY 0x40
#define IDE_INIT_DEV_PARMS 0x91
#define IDE_STANDBY 0x96
#define IDE_ACKCHANGE 0xdb
#define IDE_DOORLOCK 0xde
#define IDE_DOORUNLOCK 0xdf
#define IDE_IDENTIFY 0xec
#define IDE_EJECT 0xed
int pd_init(void);
void pd_setup(char * str, int * ints);
#ifdef MODULE
void cleanup_module( void );
#endif
static int pd_open(struct inode *inode, struct file *file);
static void do_pd_request(request_queue_t * q);
static int pd_ioctl(struct inode *inode,struct file *file,
unsigned int cmd, unsigned long arg);
static int pd_release (struct inode *inode, struct file *file);
static int pd_revalidate(kdev_t dev);
static int pd_detect(void);
static void do_pd_read(void);
static void do_pd_read_start(void);
static void do_pd_write(void);
static void do_pd_write_start(void);
static void do_pd_read_drq( void );
static void do_pd_write_done( void );
static int pd_identify (int unit);
static void pd_media_check(int unit);
static void pd_doorlock(int unit, int func);
static int pd_check_media(kdev_t dev);
static void pd_eject( int unit);
static struct hd_struct pd_hd[PD_DEVS];
static int pd_sizes[PD_DEVS];
static int pd_blocksizes[PD_DEVS];
static int pd_maxsectors[PD_DEVS];
#define PD_NAMELEN 8
struct pd_unit {
struct pi_adapter pia; /* interface to paride layer */
struct pi_adapter *pi;
int access; /* count of active opens ... */
int capacity; /* Size of this volume in sectors */
int heads; /* physical geometry */
int sectors;
int cylinders;
int drive; /* master=0 slave=1 */
int changed; /* Have we seen a disk change ? */
int removable; /* removable media device ? */
int standby;
int alt_geom;
int present;
char name[PD_NAMELEN]; /* pda, pdb, etc ... */
};
struct pd_unit pd[PD_UNITS];
/* 'unit' must be defined in all functions - either as a local or a param */
#define PD pd[unit]
#define PI PD.pi
static int pd_valid = 1; /* serialise partition checks */
static char pd_scratch[512]; /* scratch block buffer */
/* the variables below are used mainly in the I/O request engine, which
processes only one request at a time.
*/
static int pd_retries = 0; /* i/o error retry count */
static int pd_busy = 0; /* request being processed ? */
static int pd_block; /* address of next requested block */
static int pd_count; /* number of blocks still to do */
static int pd_run; /* sectors in current cluster */
static int pd_cmd; /* current command READ/WRITE */
static int pd_unit; /* unit of current request */
static int pd_dev; /* minor of current request */
static int pd_poffs; /* partition offset of current minor */
static char * pd_buf; /* buffer for request in progress */
static DECLARE_WAIT_QUEUE_HEAD(pd_wait_open);
static char *pd_errs[17] = { "ERR","INDEX","ECC","DRQ","SEEK","WRERR",
"READY","BUSY","AMNF","TK0NF","ABRT","MCR",
"IDNF","MC","UNC","???","TMO"};
/* kernel glue structures */
extern struct block_device_operations pd_fops;
static struct gendisk pd_gendisk = {
major: PD_MAJOR,
major_name: PD_NAME,
minor_shift: PD_BITS,
max_p: PD_PARTNS,
part: pd_hd,
sizes: pd_sizes,
fops: &pd_fops,
};
static struct block_device_operations pd_fops = {
owner: THIS_MODULE,
open: pd_open,
release: pd_release,
ioctl: pd_ioctl,
check_media_change: pd_check_media,
revalidate: pd_revalidate
};
void pd_init_units( void )
{ int unit, j;
pd_drive_count = 0;
for (unit=0;unit<PD_UNITS;unit++) {
PD.pi = & PD.pia;
PD.access = 0;
PD.changed = 1;
PD.capacity = 0;
PD.drive = DU[D_SLV];
PD.present = 0;
j = 0;
while ((j < PD_NAMELEN-2) && (PD.name[j]=name[j])) j++;
PD.name[j++] = 'a' + unit;
PD.name[j] = 0;
PD.alt_geom = DU[D_GEO];
PD.standby = DU[D_SBY];
if (DU[D_PRT]) pd_drive_count++;
}
}
int pd_init (void)
{ int i;
request_queue_t * q;
if (disable) return -1;
if (devfs_register_blkdev(MAJOR_NR,name,&pd_fops)) {
printk("%s: unable to get major number %d\n",
name,major);
return -1;
}
q = BLK_DEFAULT_QUEUE(MAJOR_NR);
blk_init_queue(q, DEVICE_REQUEST);
read_ahead[MAJOR_NR] = 8; /* 8 sector (4kB) read ahead */
pd_gendisk.major = major;
pd_gendisk.major_name = name;
add_gendisk(&pd_gendisk);
for(i=0;i<PD_DEVS;i++) pd_blocksizes[i] = 1024;
blksize_size[MAJOR_NR] = pd_blocksizes;
for(i=0;i<PD_DEVS;i++) pd_maxsectors[i] = cluster;
max_sectors[MAJOR_NR] = pd_maxsectors;
printk("%s: %s version %s, major %d, cluster %d, nice %d\n",
name,name,PD_VERSION,major,cluster,nice);
pd_init_units();
pd_valid = 0;
pd_gendisk.nr_real = pd_detect();
pd_valid = 1;
#ifdef MODULE
if (!pd_gendisk.nr_real) {
cleanup_module();
return -1;
}
#endif
return 0;
}
static int pd_open (struct inode *inode, struct file *file)
{ int unit = DEVICE_NR(inode->i_rdev);
if ((unit >= PD_UNITS) || (!PD.present)) return -ENODEV;
wait_event (pd_wait_open, pd_valid);
PD.access++;
if (PD.removable) {
pd_media_check(unit);
pd_doorlock(unit,IDE_DOORLOCK);
}
return 0;
}
static int pd_ioctl(struct inode *inode,struct file *file,
unsigned int cmd, unsigned long arg)
{ struct hd_geometry *geo = (struct hd_geometry *) arg;
int dev, err, unit;
if ((!inode) || (!inode->i_rdev)) return -EINVAL;
dev = MINOR(inode->i_rdev);
unit = DEVICE_NR(inode->i_rdev);
if (dev >= PD_DEVS) return -EINVAL;
if (!PD.present) return -ENODEV;
switch (cmd) {
case CDROMEJECT:
if (PD.access == 1) pd_eject(unit);
return 0;
case HDIO_GETGEO:
if (!geo) return -EINVAL;
err = verify_area(VERIFY_WRITE,geo,sizeof(*geo));
if (err) return err;
if (PD.alt_geom) {
put_user(PD.capacity/(PD_LOG_HEADS*PD_LOG_SECTS),
(short *) &geo->cylinders);
put_user(PD_LOG_HEADS, (char *) &geo->heads);
put_user(PD_LOG_SECTS, (char *) &geo->sectors);
} else {
put_user(PD.cylinders, (short *) &geo->cylinders);
put_user(PD.heads, (char *) &geo->heads);
put_user(PD.sectors, (char *) &geo->sectors);
}
put_user(pd_hd[dev].start_sect,(long *)&geo->start);
return 0;
case BLKRRPART:
if (!capable(CAP_SYS_ADMIN))
return -EACCES;
return pd_revalidate(inode->i_rdev);
case BLKGETSIZE:
case BLKGETSIZE64:
case BLKROSET:
case BLKROGET:
case BLKRASET:
case BLKRAGET:
case BLKFLSBUF:
case BLKPG:
return blk_ioctl(inode->i_rdev, cmd, arg);
default:
return -EINVAL;
}
}
static int pd_release (struct inode *inode, struct file *file)
{ kdev_t devp;
int unit;
devp = inode->i_rdev;
unit = DEVICE_NR(devp);
if ((unit >= PD_UNITS) || (PD.access <= 0))
return -EINVAL;
PD.access--;
if (!PD.access && PD.removable)
pd_doorlock(unit,IDE_DOORUNLOCK);
return 0;
}
static int pd_check_media( kdev_t dev)
{ int r, unit;
unit = DEVICE_NR(dev);
if ((unit >= PD_UNITS) || (!PD.present)) return -ENODEV;
if (!PD.removable) return 0;
pd_media_check(unit);
r = PD.changed;
PD.changed = 0;
return r;
}
static int pd_revalidate(kdev_t dev)
{ int p, unit, minor;
long flags;
unit = DEVICE_NR(dev);
if ((unit >= PD_UNITS) || (!PD.present)) return -ENODEV;
save_flags(flags);
cli();
if (PD.access > 1) {
restore_flags(flags);
return -EBUSY;
}
pd_valid = 0;
restore_flags(flags);
for (p=(PD_PARTNS-1);p>=0;p--) {
minor = p + unit*PD_PARTNS;
invalidate_device(MKDEV(MAJOR_NR, minor), 1);
pd_hd[minor].start_sect = 0;
pd_hd[minor].nr_sects = 0;
}
if (pd_identify(unit))
grok_partitions(&pd_gendisk,unit,1<<PD_BITS,PD.capacity);
pd_valid = 1;
wake_up(&pd_wait_open);
return 0;
}
#ifdef MODULE
/* Glue for modules ... */
void cleanup_module(void);
int init_module(void)
{
#ifdef PARIDE_JUMBO
{ extern paride_init();
paride_init();
}
#endif
return pd_init();
}
void cleanup_module(void)
{
int unit;
devfs_unregister_blkdev(MAJOR_NR,name);
del_gendisk(&pd_gendisk);
for (unit=0;unit<PD_UNITS;unit++)
if (PD.present) pi_release(PI);
max_sectors[MAJOR_NR] = NULL;
}
#endif
#define WR(c,r,v) pi_write_regr(PI,c,r,v)
#define RR(c,r) (pi_read_regr(PI,c,r))
#define DRIVE (0xa0+0x10*PD.drive)
/* ide command interface */
static void pd_print_error( int unit, char * msg, int status )
{ int i;
printk("%s: %s: status = 0x%x =",PD.name,msg,status);
for(i=0;i<18;i++) if (status & (1<<i)) printk(" %s",pd_errs[i]);
printk("\n");
}
static void pd_reset( int unit ) /* called only for MASTER drive */
{ pi_connect(PI);
WR(1,6,4);
udelay(50);
WR(1,6,0);
pi_disconnect(PI);
udelay(250);
}
#define DBMSG(msg) ((verbose>1)?(msg):NULL)
static int pd_wait_for( int unit, int w, char * msg ) /* polled wait */
{ int k, r, e;
k=0;
while(k < PD_SPIN) {
r = RR(1,6);
k++;
if (((r & w) == w) && !(r & STAT_BUSY)) break;
udelay(PD_SPIN_DEL);
}
e = (RR(0,1)<<8) + RR(0,7);
if (k >= PD_SPIN) e |= ERR_TMO;
if ((e & (STAT_ERR|ERR_TMO)) && (msg != NULL))
pd_print_error(unit,msg,e);
return e;
}
static void pd_send_command( int unit, int n, int s, int h,
int c0, int c1, int func )
{
WR(0,6,DRIVE+h);
WR(0,1,0); /* the IDE task file */
WR(0,2,n);
WR(0,3,s);
WR(0,4,c0);
WR(0,5,c1);
WR(0,7,func);
udelay(1);
}
static void pd_ide_command( int unit, int func, int block, int count )
/* Don't use this call if the capacity is zero. */
{ int c1, c0, h, s;
s = ( block % PD.sectors) + 1;
h = ( block / PD.sectors) % PD.heads;
c0 = ( block / (PD.sectors*PD.heads)) % 256;
c1 = ( block / (PD.sectors*PD.heads*256));
pd_send_command(unit,count,s,h,c0,c1,func);
}
/* According to the ATA standard, the default CHS geometry should be
available following a reset. Some Western Digital drives come up
in a mode where only LBA addresses are accepted until the device
parameters are initialised.
*/
static void pd_init_dev_parms( int unit )
{ pi_connect(PI);
pd_wait_for(unit,0,DBMSG("before init_dev_parms"));
pd_send_command(unit,PD.sectors,0,PD.heads-1,0,0,IDE_INIT_DEV_PARMS);
udelay(300);
pd_wait_for(unit,0,"Initialise device parameters");
pi_disconnect(PI);
}
static void pd_doorlock( int unit, int func )
{ pi_connect(PI);
if (pd_wait_for(unit,STAT_READY,"Lock") & STAT_ERR) {
pi_disconnect(PI);
return;
}
pd_send_command(unit,1,0,0,0,0,func);
pd_wait_for(unit,STAT_READY,"Lock done");
pi_disconnect(PI);
}
static void pd_eject( int unit )
{ pi_connect(PI);
pd_wait_for(unit,0,DBMSG("before unlock on eject"));
pd_send_command(unit,1,0,0,0,0,IDE_DOORUNLOCK);
pd_wait_for(unit,0,DBMSG("after unlock on eject"));
pd_wait_for(unit,0,DBMSG("before eject"));
pd_send_command(unit,0,0,0,0,0,IDE_EJECT);
pd_wait_for(unit,0,DBMSG("after eject"));
pi_disconnect(PI);
}
static void pd_media_check( int unit )
{ int r;
pi_connect(PI);
r = pd_wait_for(unit,STAT_READY,DBMSG("before media_check"));
if (!(r & STAT_ERR)) {
pd_send_command(unit,1,1,0,0,0,IDE_READ_VRFY);
r = pd_wait_for(unit,STAT_READY,DBMSG("RDY after READ_VRFY"));
} else PD.changed = 1; /* say changed if other error */
if (r & ERR_MC) {
PD.changed = 1;
pd_send_command(unit,1,0,0,0,0,IDE_ACKCHANGE);
pd_wait_for(unit,STAT_READY,DBMSG("RDY after ACKCHANGE"));
pd_send_command(unit,1,1,0,0,0,IDE_READ_VRFY);
r = pd_wait_for(unit,STAT_READY,DBMSG("RDY after VRFY"));
}
pi_disconnect(PI);
}
static void pd_standby_off( int unit )
{ pi_connect(PI);
pd_wait_for(unit,0,DBMSG("before STANDBY"));
pd_send_command(unit,0,0,0,0,0,IDE_STANDBY);
pd_wait_for(unit,0,DBMSG("after STANDBY"));
pi_disconnect(PI);
}
#define word_val(n) ((pd_scratch[2*n]&0xff)+256*(pd_scratch[2*n+1]&0xff))
static int pd_identify( int unit )
{ int j;
char id[PD_ID_LEN+1];
/* WARNING: here there may be dragons. reset() applies to both drives,
but we call it only on probing the MASTER. This should allow most
common configurations to work, but be warned that a reset can clear
settings on the SLAVE drive.
*/
if (PD.drive == 0) pd_reset(unit);
pi_connect(PI);
WR(0,6,DRIVE);
pd_wait_for(unit,0,DBMSG("before IDENT"));
pd_send_command(unit,1,0,0,0,0,IDE_IDENTIFY);
if (pd_wait_for(unit,STAT_DRQ,DBMSG("IDENT DRQ")) & STAT_ERR) {
pi_disconnect(PI);
return 0;
}
pi_read_block(PI,pd_scratch,512);
pi_disconnect(PI);
PD.sectors = word_val(6);
PD.heads = word_val(3);
PD.cylinders = word_val(1);
PD.capacity = PD.sectors*PD.heads*PD.cylinders;
for(j=0;j<PD_ID_LEN;j++) id[j^1] = pd_scratch[j+PD_ID_OFF];
j = PD_ID_LEN-1;
while ((j >= 0) && (id[j] <= 0x20)) j--;
j++; id[j] = 0;
PD.removable = (word_val(0) & 0x80);
printk("%s: %s, %s, %d blocks [%dM], (%d/%d/%d), %s media\n",
PD.name,id,
PD.drive?"slave":"master",
PD.capacity,PD.capacity/2048,
PD.cylinders,PD.heads,PD.sectors,
PD.removable?"removable":"fixed");
if (PD.capacity) pd_init_dev_parms(unit);
if (!PD.standby) pd_standby_off(unit);
return 1;
}
static int pd_probe_drive( int unit )
{
if (PD.drive == -1) {
for (PD.drive=0;PD.drive<=1;PD.drive++)
if (pd_identify(unit))
return 1;
return 0;
}
return pd_identify(unit);
}
static int pd_detect( void )
{ int k, unit;
k = 0;
if (pd_drive_count == 0) { /* nothing spec'd - so autoprobe for 1 */
unit = 0;
if (pi_init(PI,1,-1,-1,-1,-1,-1,pd_scratch,
PI_PD,verbose,PD.name)) {
if (pd_probe_drive(unit)) {
PD.present = 1;
k = 1;
} else pi_release(PI);
}
} else for (unit=0;unit<PD_UNITS;unit++) if (DU[D_PRT])
if (pi_init(PI,0,DU[D_PRT],DU[D_MOD],DU[D_UNI],
DU[D_PRO],DU[D_DLY],pd_scratch,
PI_PD,verbose,PD.name)) {
if (pd_probe_drive(unit)) {
PD.present = 1;
k = unit+1;
} else pi_release(PI);
}
for (unit=0;unit<PD_UNITS;unit++)
register_disk(&pd_gendisk,MKDEV(MAJOR_NR,unit<<PD_BITS),
PD_PARTNS,&pd_fops,
PD.present?PD.capacity:0);
/* We lie about the number of drives found, as the generic partition
scanner assumes that the drives are numbered sequentially from 0.
This can result in some bogus error messages if non-sequential
drive numbers are used.
*/
if (k)
return k;
printk("%s: no valid drive found\n",name);
return 0;
}
/* The i/o request engine */
static int pd_ready( void )
{ int unit = pd_unit;
return (!(RR(1,6) & STAT_BUSY)) ;
}
static void do_pd_request (request_queue_t * q)
{ struct buffer_head * bh;
int unit;
if (pd_busy) return;
repeat:
if (QUEUE_EMPTY || (CURRENT->rq_status == RQ_INACTIVE)) return;
INIT_REQUEST;
pd_dev = MINOR(CURRENT->rq_dev);
pd_unit = unit = DEVICE_NR(CURRENT->rq_dev);
pd_block = CURRENT->sector;
pd_run = CURRENT->nr_sectors;
pd_count = CURRENT->current_nr_sectors;
bh = CURRENT->bh;
if ((pd_dev >= PD_DEVS) ||
((pd_block+pd_count) > pd_hd[pd_dev].nr_sects)) {
end_request(0);
goto repeat;
}
pd_cmd = CURRENT->cmd;
pd_poffs = pd_hd[pd_dev].start_sect;
pd_block += pd_poffs;
pd_buf = CURRENT->buffer;
pd_retries = 0;
pd_busy = 1;
if (pd_cmd == READ) pi_do_claimed(PI,do_pd_read);
else if (pd_cmd == WRITE) pi_do_claimed(PI,do_pd_write);
else { pd_busy = 0;
end_request(0);
goto repeat;
}
}
static void pd_next_buf( int unit )
{ long saved_flags;
spin_lock_irqsave(&io_request_lock,saved_flags);
end_request(1);
if (!pd_run) { spin_unlock_irqrestore(&io_request_lock,saved_flags);
return;
}
/* paranoia */
if (QUEUE_EMPTY ||
(CURRENT->cmd != pd_cmd) ||
(MINOR(CURRENT->rq_dev) != pd_dev) ||
(CURRENT->rq_status == RQ_INACTIVE) ||
(CURRENT->sector+pd_poffs != pd_block))
printk("%s: OUCH: request list changed unexpectedly\n",
PD.name);
pd_count = CURRENT->current_nr_sectors;
pd_buf = CURRENT->buffer;
spin_unlock_irqrestore(&io_request_lock,saved_flags);
}
static void do_pd_read( void )
{ ps_set_intr(do_pd_read_start,0,0,nice);
}
static void do_pd_read_start( void )
{ int unit = pd_unit;
long saved_flags;
pd_busy = 1;
pi_connect(PI);
if (pd_wait_for(unit,STAT_READY,"do_pd_read") & STAT_ERR) {
pi_disconnect(PI);
if (pd_retries < PD_MAX_RETRIES) {
pd_retries++;
pi_do_claimed(PI,do_pd_read_start);
return;
}
spin_lock_irqsave(&io_request_lock,saved_flags);
end_request(0);
pd_busy = 0;
do_pd_request(NULL);
spin_unlock_irqrestore(&io_request_lock,saved_flags);
return;
}
pd_ide_command(unit,IDE_READ,pd_block,pd_run);
ps_set_intr(do_pd_read_drq,pd_ready,PD_TMO,nice);
}
static void do_pd_read_drq( void )
{ int unit = pd_unit;
long saved_flags;
while (1) {
if (pd_wait_for(unit,STAT_DRQ,"do_pd_read_drq") & STAT_ERR) {
pi_disconnect(PI);
if (pd_retries < PD_MAX_RETRIES) {
pd_retries++;
pi_do_claimed(PI,do_pd_read_start);
return;
}
spin_lock_irqsave(&io_request_lock,saved_flags);
end_request(0);
pd_busy = 0;
do_pd_request(NULL);
spin_unlock_irqrestore(&io_request_lock,saved_flags);
return;
}
pi_read_block(PI,pd_buf,512);
pd_count--; pd_run--;
pd_buf += 512;
pd_block++;
if (!pd_run) break;
if (!pd_count) pd_next_buf(unit);
}
pi_disconnect(PI);
spin_lock_irqsave(&io_request_lock,saved_flags);
end_request(1);
pd_busy = 0;
do_pd_request(NULL);
spin_unlock_irqrestore(&io_request_lock,saved_flags);
}
static void do_pd_write( void )
{ ps_set_intr(do_pd_write_start,0,0,nice);
}
static void do_pd_write_start( void )
{ int unit = pd_unit;
long saved_flags;
pd_busy = 1;
pi_connect(PI);
if (pd_wait_for(unit,STAT_READY,"do_pd_write") & STAT_ERR) {
pi_disconnect(PI);
if (pd_retries < PD_MAX_RETRIES) {
pd_retries++;
pi_do_claimed(PI,do_pd_write_start);
return;
}
spin_lock_irqsave(&io_request_lock,saved_flags);
end_request(0);
pd_busy = 0;
do_pd_request(NULL);
spin_unlock_irqrestore(&io_request_lock,saved_flags);
return;
}
pd_ide_command(unit,IDE_WRITE,pd_block,pd_run);
while (1) {
if (pd_wait_for(unit,STAT_DRQ,"do_pd_write_drq") & STAT_ERR) {
pi_disconnect(PI);
if (pd_retries < PD_MAX_RETRIES) {
pd_retries++;
pi_do_claimed(PI,do_pd_write_start);
return;
}
spin_lock_irqsave(&io_request_lock,saved_flags);
end_request(0);
pd_busy = 0;
do_pd_request(NULL);
spin_unlock_irqrestore(&io_request_lock,saved_flags);
return;
}
pi_write_block(PI,pd_buf,512);
pd_count--; pd_run--;
pd_buf += 512;
pd_block++;
if (!pd_run) break;
if (!pd_count) pd_next_buf(unit);
}
ps_set_intr(do_pd_write_done,pd_ready,PD_TMO,nice);
}
static void do_pd_write_done( void )
{ int unit = pd_unit;
long saved_flags;
if (pd_wait_for(unit,STAT_READY,"do_pd_write_done") & STAT_ERR) {
pi_disconnect(PI);
if (pd_retries < PD_MAX_RETRIES) {
pd_retries++;
pi_do_claimed(PI,do_pd_write_start);
return;
}
spin_lock_irqsave(&io_request_lock,saved_flags);
end_request(0);
pd_busy = 0;
do_pd_request(NULL);
spin_unlock_irqrestore(&io_request_lock,saved_flags);
return;
}
pi_disconnect(PI);
spin_lock_irqsave(&io_request_lock,saved_flags);
end_request(1);
pd_busy = 0;
do_pd_request(NULL);
spin_unlock_irqrestore(&io_request_lock,saved_flags);
}
/* end of pd.c */
MODULE_LICENSE("GPL");
|