Viewing file:  pci-bigsur.c (5.22 KB) -rw-r--r--
Select action/file-type:
 (+) |  (+) |  (+) | Code (+) | Session (+) |  (+) | SDB (+) |  (+) |  (+) |  (+) |  (+) |  (+) |
/*
* linux/arch/sh/kernel/pci-bigsur.c
*
* By Dustin McIntire (dustin@sensoria.com) (c)2001
* May be copied or modified under the terms of the GNU General Public
* License. See linux/COPYING for more information.
*
* PCI initialization for the Hitachi Big Sur Evaluation Board
*/
#include <linux/config.h>
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/pci.h>
#include <asm/io.h>
#include <asm/pci-sh7751.h>
#include <asm/bigsur.h>
#define PCI_REG(reg) (SH7751_PCIREG_BASE+reg)
/*
* Initialize the Big Sur PCI interface
* Setup hardware to be Central Funtion
* Copy the BSR regs to the PCI interface
* Setup PCI windows into local RAM
*/
int __init pcibios_init_platform(void) {
u32 reg;
u32 word;
PCIDBG(1,"PCI: bigsur_pci_init called\n");
/* Set the BCR's to enable PCI access */
reg = inl(SH7751_BCR1);
reg |= 0x80000;
outl(reg, SH7751_BCR1);
/* Setup the host hardware */
if(inl(PCI_REG(SH7751_PCICONF0)) !=
(u32)((SH7751_DEVICE_ID <<16) | (SH7751_VENDOR_ID))) {
printk("PCI: Unkown PCI host bridge.\n");
return 0;
}
printk("PCI: SH7751 PCI host bridge found.\n");
/* Turn the clocks back on (not done in reset)*/
outl(0, PCI_REG(SH7751_PCICLKR));
/* Clear Powerdown IRQ's (not done in reset) */
word = SH7751_PCIPINT_D3 | SH7751_PCIPINT_D0;
outl(word, PCI_REG(SH7751_PCICLKR));
/* toggle PCI reset pin */
word = SH7751_PCICR_PREFIX | SH7751_PCICR_PRST;
outl(word,PCI_REG(SH7751_PCICR));
/* Wait for a long time... not 1 sec. but long enough */
mdelay(100);
word = SH7751_PCICR_PREFIX;
outl(word,PCI_REG(SH7751_PCICR));
/* set the command/status bits to:
* Wait Cycle Control + Parity Enable + Bus Master +
* Mem space enable
*/
word = SH7751_PCICONF1_WCC | SH7751_PCICONF1_PER |
SH7751_PCICONF1_BUM | SH7751_PCICONF1_MES;
outl(word, PCI_REG(SH7751_PCICONF1));
/* define this host as the host bridge */
word = SH7751_PCI_HOST_BRIDGE << 24;
outl(word, PCI_REG(SH7751_PCICONF2));
/* Set IO and Mem windows to local address
* Make PCI and local address the same for easy 1 to 1 mapping
* Window0 = BIGSUR_LSR0_SIZE @ non-cached CS3 base = SDRAM
* Window1 = BIGSUR_LSR1_SIZE @ cached CS3 base = SDRAM
*/
word = BIGSUR_LSR0_SIZE - 1;
outl(word, PCI_REG(SH7751_PCILSR0));
word = BIGSUR_LSR1_SIZE - 1;
outl(word, PCI_REG(SH7751_PCILSR1));
/* Set the values on window 0 PCI config registers */
word = P2SEGADDR(SH7751_CS3_BASE_ADDR);
outl(word, PCI_REG(SH7751_PCILAR0));
outl(word, PCI_REG(SH7751_PCICONF5));
/* Set the values on window 1 PCI config registers */
word = PHYSADDR(SH7751_CS3_BASE_ADDR);
outl(word, PCI_REG(SH7751_PCILAR1));
outl(word, PCI_REG(SH7751_PCICONF6));
/* Set the local 16MB PCI memory space window to
* the lowest PCI mapped address
*/
word = PCIBIOS_MIN_MEM & SH7751_PCIMBR_MASK;
PCIDBG(2,"PCI: Setting upper bits of Memory window to 0x%x\n", word);
outl(word , PCI_REG(SH7751_PCIMBR));
/* Map IO space into PCI IO window
* The IO window is 64K-PCIBIOS_MIN_IO in size
* IO addresses will be translated to the
* PCI IO window base address
*/
PCIDBG(3,"PCI: Mapping IO address 0x%x - 0x%x to base 0x%x\n", PCIBIOS_MIN_IO,
(64*1024), SH7751_PCI_IO_BASE+PCIBIOS_MIN_IO);
bigsur_port_map(PCIBIOS_MIN_IO, (64*1024), SH7751_PCI_IO_BASE+PCIBIOS_MIN_IO,0);
/* Make sure the MSB's of IO window are set to access PCI space correctly */
word = PCIBIOS_MIN_IO & SH7751_PCIIOBR_MASK;
PCIDBG(2,"PCI: Setting upper bits of IO window to 0x%x\n", word);
outl(word, PCI_REG(SH7751_PCIIOBR));
/* Set PCI WCRx, BCRx's, copy from BSC locations */
word = inl(SH7751_BCR1);
/* check BCR for SDRAM in area 3 */
if(((word >> 3) & 1) == 0) {
printk("PCI: Area 3 is not configured for SDRAM. BCR1=0x%x\n", word);
return 0;
}
outl(word, PCI_REG(SH7751_PCIBCR1));
word = (u16)inw(SH7751_BCR2);
/* check BCR2 for 32bit SDRAM interface*/
if(((word >> 6) & 0x3) != 0x3) {
printk("PCI: Area 3 is not 32 bit SDRAM. BCR2=0x%x\n", word);
return 0;
}
outl(word, PCI_REG(SH7751_PCIBCR2));
/* configure the wait control registers */
word = inl(SH7751_WCR1);
outl(word, PCI_REG(SH7751_PCIWCR1));
word = inl(SH7751_WCR2);
outl(word, PCI_REG(SH7751_PCIWCR2));
word = inl(SH7751_WCR3);
outl(word, PCI_REG(SH7751_PCIWCR3));
word = inl(SH7751_MCR);
outl(word, PCI_REG(SH7751_PCIMCR));
/* NOTE: I'm ignoring the PCI error IRQs for now..
* TODO: add support for the internal error interrupts and
* DMA interrupts...
*/
/* SH7751 init done, set central function init complete */
word = SH7751_PCICR_PREFIX | SH7751_PCICR_CFIN;
outl(word,PCI_REG(SH7751_PCICR));
PCIDBG(2,"PCI: bigsur_pci_init finished\n");
return 1;
}
int pcibios_map_platform_irq(u8 slot, u8 pin)
{
/* The Big Sur can be used in a CPCI chassis, but the SH7751 PCI interface is on the
* wrong end of the board so that it can also support a V320 CPI interface chip...
* Therefor the IRQ mapping is somewhat use dependent... I'l assume a linear map for
* now, i.e. INTA=slot0,pin0... INTD=slot3,pin0...
*/
int irq = (slot + pin-1)%4 + BIGSUR_SH7751_PCI_IRQ_BASE;
PCIDBG(2,"PCI: Mapping Big Sur IRQ for slot %d, pin %c to irq %d\n", slot, pin-1+'A', irq);
return irq;
}
|