Viewing file:  gdb_hook.c (5.28 KB) -rw-r--r--
Select action/file-type:
 (+) |  (+) |  (+) | Code (+) | Session (+) |  (+) | SDB (+) |  (+) |  (+) |  (+) |  (+) |  (+) |
/*
* Carsten Langgaard, carstenl@mips.com
* Copyright (C) 2000 MIPS Technologies, Inc. All rights reserved.
*
* ########################################################################
*
* This program is free software; you can distribute it and/or modify it
* under the terms of the GNU General Public License (Version 2) as
* published by the Free Software Foundation.
*
* This program is distributed in the hope it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
* for more details.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
*
* ########################################################################
*
* This is the interface to the remote debugger stub.
*
*/
#include <linux/serialP.h>
#include <linux/serial_reg.h>
#include <asm/serial.h>
#include <asm/io.h>
static struct serial_state rs_table[RS_TABLE_SIZE] = {
SERIAL_PORT_DFNS /* Defined in serial.h */
};
static struct async_struct kdb_port_info = {0};
int (*generic_putDebugChar)(char);
char (*generic_getDebugChar)(void);
static __inline__ unsigned int serial_in(struct async_struct *info, int offset)
{
return inb(info->port + offset);
}
static __inline__ void serial_out(struct async_struct *info, int offset,
int value)
{
outb(value, info->port+offset);
}
void rs_kgdb_hook(int tty_no) {
int t;
struct serial_state *ser = &rs_table[tty_no];
kdb_port_info.state = ser;
kdb_port_info.magic = SERIAL_MAGIC;
kdb_port_info.port = ser->port;
kdb_port_info.flags = ser->flags;
/*
* Clear all interrupts
*/
serial_in(&kdb_port_info, UART_LSR);
serial_in(&kdb_port_info, UART_RX);
serial_in(&kdb_port_info, UART_IIR);
serial_in(&kdb_port_info, UART_MSR);
/*
* Now, initialize the UART
*/
serial_out(&kdb_port_info, UART_LCR, UART_LCR_WLEN8); /* reset DLAB */
if (kdb_port_info.flags & ASYNC_FOURPORT) {
kdb_port_info.MCR = UART_MCR_DTR | UART_MCR_RTS;
t = UART_MCR_DTR | UART_MCR_OUT1;
} else {
kdb_port_info.MCR
= UART_MCR_DTR | UART_MCR_RTS | UART_MCR_OUT2;
t = UART_MCR_DTR | UART_MCR_RTS;
}
kdb_port_info.MCR = t; /* no interrupts, please */
serial_out(&kdb_port_info, UART_MCR, kdb_port_info.MCR);
/*
* and set the speed of the serial port
* (currently hardwired to 9600 8N1
*/
/* baud rate is fixed to 9600 (is this sufficient?)*/
t = kdb_port_info.state->baud_base / 9600;
/* set DLAB */
serial_out(&kdb_port_info, UART_LCR, UART_LCR_WLEN8 | UART_LCR_DLAB);
serial_out(&kdb_port_info, UART_DLL, t & 0xff);/* LS of divisor */
serial_out(&kdb_port_info, UART_DLM, t >> 8); /* MS of divisor */
/* reset DLAB */
serial_out(&kdb_port_info, UART_LCR, UART_LCR_WLEN8);
}
int putDebugChar(char c)
{
return generic_putDebugChar(c);
}
char getDebugChar(void)
{
return generic_getDebugChar();
}
int rs_putDebugChar(char c)
{
if (!kdb_port_info.state) { /* need to init device first */
return 0;
}
while ((serial_in(&kdb_port_info, UART_LSR) & UART_LSR_THRE) == 0)
;
serial_out(&kdb_port_info, UART_TX, c);
return 1;
}
char rs_getDebugChar(void)
{
if (!kdb_port_info.state) { /* need to init device first */
return 0;
}
while (!(serial_in(&kdb_port_info, UART_LSR) & 1))
;
return(serial_in(&kdb_port_info, UART_RX));
}
#ifdef CONFIG_MIPS_ATLAS
#include <asm/mips-boards/atlas.h>
#include <asm/mips-boards/saa9730_uart.h>
#define INB(a) inb((unsigned long)a)
#define OUTB(x,a) outb(x,(unsigned long)a)
/*
* This is the interface to the remote debugger stub
* if the Philips part is used for the debug port,
* called from the platform setup code.
*
* PCI init will not have been done yet, we make a
* universal assumption about the way the bootloader (YAMON)
* have located and set up the chip.
*/
static t_uart_saa9730_regmap *kgdb_uart = (void *)(ATLAS_SAA9730_REG + SAA9730_UART_REGS_ADDR);
static int saa9730_kgdb_active = 0;
void saa9730_kgdb_hook(void)
{
volatile unsigned char t;
/*
* Clear all interrupts
*/
t = INB(&kgdb_uart->Lsr);
t += INB(&kgdb_uart->Msr);
t += INB(&kgdb_uart->Thr_Rbr);
t += INB(&kgdb_uart->Iir_Fcr);
/*
* Now, initialize the UART
*/
/* 8 data bits, one stop bit, no parity */
OUTB(SAA9730_LCR_DATA8, &kgdb_uart->Lcr);
/* baud rate is fixed to 9600 (is this sufficient?)*/
OUTB(0, &kgdb_uart->BaudDivMsb); /* HACK - Assumes standard crystal */
OUTB(23, &kgdb_uart->BaudDivLsb); /* HACK - known for MIPS Atlas */
/* Set RTS/DTR active */
OUTB(SAA9730_MCR_DTR | SAA9730_MCR_RTS, &kgdb_uart->Mcr);
saa9730_kgdb_active = 1;
}
int saa9730_putDebugChar(char c)
{
if (!saa9730_kgdb_active) { /* need to init device first */
return 0;
}
while (!(INB(&kgdb_uart->Lsr) & SAA9730_LSR_THRE))
;
OUTB(c, &kgdb_uart->Thr_Rbr);
return 1;
}
char saa9730_getDebugChar(void)
{
char c;
if (!saa9730_kgdb_active) { /* need to init device first */
return 0;
}
while (!(INB(&kgdb_uart->Lsr) & SAA9730_LSR_DR))
;
c = INB(&kgdb_uart->Thr_Rbr);
return(c);
}
#endif
|