Viewing file:  setup.c (3.58 KB) -rw-r--r--
Select action/file-type:
 (+) |  (+) |  (+) | Code (+) | Session (+) |  (+) | SDB (+) |  (+) |  (+) |  (+) |  (+) |  (+) |
/*
* Setup pointers to hardware-dependent routines.
*
* This file is subject to the terms and conditions of the GNU General Public
* License. See the file "COPYING" in the main directory of this archive
* for more details.
*
* Copyright (C) 1996, 1997, 1998, 2001 by Ralf Baechle
* Copyright (C) 2001 MIPS Technologies, Inc.
*/
#include <linux/config.h>
#include <linux/hdreg.h>
#include <linux/init.h>
#include <linux/ioport.h>
#include <linux/sched.h>
#include <linux/interrupt.h>
#include <linux/mm.h>
#include <linux/console.h>
#include <linux/fb.h>
#include <linux/mc146818rtc.h>
#include <linux/ide.h>
#include <asm/bootinfo.h>
#include <asm/keyboard.h>
#include <asm/irq.h>
#include <asm/jazz.h>
#include <asm/jazzdma.h>
#include <asm/ptrace.h>
#include <asm/reboot.h>
#include <asm/io.h>
#include <asm/pgtable.h>
/*
* Initial irq handlers.
*/
static void no_action(int cpl, void *dev_id, struct pt_regs *regs) { }
/*
* IRQ2 is cascade interrupt to second interrupt controller
*/
static struct irqaction irq2 = { no_action, 0, 0, "cascade", NULL, NULL};
extern asmlinkage void jazz_handle_int(void);
extern void jazz_machine_restart(char *command);
extern void jazz_machine_halt(void);
extern void jazz_machine_power_off(void);
extern struct ide_ops std_ide_ops;
extern struct rtc_ops jazz_rtc_ops;
extern struct kbd_ops jazz_kbd_ops;
extern struct fd_ops *fd_ops;
extern struct fd_ops jazz_fd_ops;
void (*board_time_init)(struct irqaction *irq);
static void __init jazz_time_init(struct irqaction *irq)
{
/* set the clock to 100 Hz */
r4030_write_reg32(JAZZ_TIMER_INTERVAL, 9);
i8259_setup_irq(JAZZ_TIMER_IRQ, irq);
}
static void __init jazz_irq_setup(void)
{
set_except_vector(0, jazz_handle_int);
r4030_write_reg16(JAZZ_IO_IRQ_ENABLE,
JAZZ_IE_ETHERNET |
JAZZ_IE_SCSI |
JAZZ_IE_SERIAL1 |
JAZZ_IE_SERIAL2 |
JAZZ_IE_PARALLEL |
JAZZ_IE_FLOPPY);
r4030_read_reg16(JAZZ_IO_IRQ_SOURCE); /* clear pending IRQs */
r4030_read_reg32(JAZZ_R4030_INVAL_ADDR); /* clear error bits */
change_cp0_status(ST0_IM, IE_IRQ4 | IE_IRQ3 | IE_IRQ2 | IE_IRQ1);
/* set the clock to 100 Hz */
r4030_write_reg32(JAZZ_TIMER_INTERVAL, 9);
request_region(0x20, 0x20, "pic1");
request_region(0xa0, 0x20, "pic2");
i8259_setup_irq(2, &irq2);
}
void __init jazz_setup(void)
{
add_wired_entry (0x02000017, 0x03c00017, 0xe0000000, PM_64K);
add_wired_entry (0x02400017, 0x02440017, 0xe2000000, PM_16M);
add_wired_entry (0x01800017, 0x01000017, 0xe4000000, PM_4M);
irq_setup = jazz_irq_setup;
mips_io_port_base = JAZZ_PORT_BASE;
if (mips_machtype == MACH_MIPS_MAGNUM_4000)
EISA_bus = 1;
isa_slot_offset = 0xe3000000;
request_region(0x00,0x20,"dma1");
request_region(0x40,0x20,"timer");
request_region(0x80,0x10,"dma page reg");
request_region(0xc0,0x20,"dma2");
board_time_init = jazz_time_init;
/* The RTC is outside the port address space */
_machine_restart = jazz_machine_restart;
_machine_halt = jazz_machine_halt;
_machine_power_off = jazz_machine_power_off;
#ifdef CONFIG_BLK_DEV_IDE
ide_ops = &std_ide_ops;
#endif
#ifdef CONFIG_BLK_DEV_FD
fd_ops = &jazz_fd_ops;
#endif
#ifdef CONFIG_VT
conswitchp = &dummy_con;
#endif
#warning "Somebody should check if screen_info is ok for Jazz."
screen_info = (struct screen_info) {
0, 0, /* orig-x, orig-y */
0, /* unused */
0, /* orig_video_page */
0, /* orig_video_mode */
160, /* orig_video_cols */
0, 0, 0, /* unused, ega_bx, unused */
64, /* orig_video_lines */
0, /* orig_video_isVGA */
16 /* orig_video_points */
};
rtc_ops = &jazz_rtc_ops;
kbd_ops = &jazz_kbd_ops;
vdma_init();
}
|