Viewing file:  header.h (20.31 KB) -rw-r--r--
Select action/file-type:
 (+) |  (+) |  (+) | Code (+) | Session (+) |  (+) | SDB (+) |  (+) |  (+) |  (+) |  (+) |  (+) |
/*
* $Id: header.h,v 1.9 2002/12/26 20:24:50 mj Exp $
*
* The PCI Library -- PCI Header Structure (extracted from <linux/pci.h>)
*
* Copyright (c) 1997--2002 Martin Mares <mj@ucw.cz>
*
* Can be freely distributed and used under the terms of the GNU GPL.
*/
/*
* Under PCI, each device has 256 bytes of configuration address space,
* of which the first 64 bytes are standardized as follows:
*/
#define PCI_VENDOR_ID 0x00 /* 16 bits */
#define PCI_DEVICE_ID 0x02 /* 16 bits */
#define PCI_COMMAND 0x04 /* 16 bits */
#define PCI_COMMAND_IO 0x1 /* Enable response in I/O space */
#define PCI_COMMAND_MEMORY 0x2 /* Enable response in Memory space */
#define PCI_COMMAND_MASTER 0x4 /* Enable bus mastering */
#define PCI_COMMAND_SPECIAL 0x8 /* Enable response to special cycles */
#define PCI_COMMAND_INVALIDATE 0x10 /* Use memory write and invalidate */
#define PCI_COMMAND_VGA_PALETTE 0x20 /* Enable palette snooping */
#define PCI_COMMAND_PARITY 0x40 /* Enable parity checking */
#define PCI_COMMAND_WAIT 0x80 /* Enable address/data stepping */
#define PCI_COMMAND_SERR 0x100 /* Enable SERR */
#define PCI_COMMAND_FAST_BACK 0x200 /* Enable back-to-back writes */
#define PCI_STATUS 0x06 /* 16 bits */
#define PCI_STATUS_CAP_LIST 0x10 /* Support Capability List */
#define PCI_STATUS_66MHZ 0x20 /* Support 66 Mhz PCI 2.1 bus */
#define PCI_STATUS_UDF 0x40 /* Support User Definable Features [obsolete] */
#define PCI_STATUS_FAST_BACK 0x80 /* Accept fast-back to back */
#define PCI_STATUS_PARITY 0x100 /* Detected parity error */
#define PCI_STATUS_DEVSEL_MASK 0x600 /* DEVSEL timing */
#define PCI_STATUS_DEVSEL_FAST 0x000
#define PCI_STATUS_DEVSEL_MEDIUM 0x200
#define PCI_STATUS_DEVSEL_SLOW 0x400
#define PCI_STATUS_SIG_TARGET_ABORT 0x800 /* Set on target abort */
#define PCI_STATUS_REC_TARGET_ABORT 0x1000 /* Master ack of " */
#define PCI_STATUS_REC_MASTER_ABORT 0x2000 /* Set on master abort */
#define PCI_STATUS_SIG_SYSTEM_ERROR 0x4000 /* Set when we drive SERR */
#define PCI_STATUS_DETECTED_PARITY 0x8000 /* Set on parity error */
#define PCI_CLASS_REVISION 0x08 /* High 24 bits are class, low 8
revision */
#define PCI_REVISION_ID 0x08 /* Revision ID */
#define PCI_CLASS_PROG 0x09 /* Reg. Level Programming Interface */
#define PCI_CLASS_DEVICE 0x0a /* Device class */
#define PCI_CACHE_LINE_SIZE 0x0c /* 8 bits */
#define PCI_LATENCY_TIMER 0x0d /* 8 bits */
#define PCI_HEADER_TYPE 0x0e /* 8 bits */
#define PCI_HEADER_TYPE_NORMAL 0
#define PCI_HEADER_TYPE_BRIDGE 1
#define PCI_HEADER_TYPE_CARDBUS 2
#define PCI_BIST 0x0f /* 8 bits */
#define PCI_BIST_CODE_MASK 0x0f /* Return result */
#define PCI_BIST_START 0x40 /* 1 to start BIST, 2 secs or less */
#define PCI_BIST_CAPABLE 0x80 /* 1 if BIST capable */
/*
* Base addresses specify locations in memory or I/O space.
* Decoded size can be determined by writing a value of
* 0xffffffff to the register, and reading it back. Only
* 1 bits are decoded.
*/
#define PCI_BASE_ADDRESS_0 0x10 /* 32 bits */
#define PCI_BASE_ADDRESS_1 0x14 /* 32 bits [htype 0,1 only] */
#define PCI_BASE_ADDRESS_2 0x18 /* 32 bits [htype 0 only] */
#define PCI_BASE_ADDRESS_3 0x1c /* 32 bits */
#define PCI_BASE_ADDRESS_4 0x20 /* 32 bits */
#define PCI_BASE_ADDRESS_5 0x24 /* 32 bits */
#define PCI_BASE_ADDRESS_SPACE 0x01 /* 0 = memory, 1 = I/O */
#define PCI_BASE_ADDRESS_SPACE_IO 0x01
#define PCI_BASE_ADDRESS_SPACE_MEMORY 0x00
#define PCI_BASE_ADDRESS_MEM_TYPE_MASK 0x06
#define PCI_BASE_ADDRESS_MEM_TYPE_32 0x00 /* 32 bit address */
#define PCI_BASE_ADDRESS_MEM_TYPE_1M 0x02 /* Below 1M [obsolete] */
#define PCI_BASE_ADDRESS_MEM_TYPE_64 0x04 /* 64 bit address */
#define PCI_BASE_ADDRESS_MEM_PREFETCH 0x08 /* prefetchable? */
#define PCI_BASE_ADDRESS_MEM_MASK (~0x0fUL)
#define PCI_BASE_ADDRESS_IO_MASK (~0x03UL)
/* bit 1 is reserved if address_space = 1 */
/* Header type 0 (normal devices) */
#define PCI_CARDBUS_CIS 0x28
#define PCI_SUBSYSTEM_VENDOR_ID 0x2c
#define PCI_SUBSYSTEM_ID 0x2e
#define PCI_ROM_ADDRESS 0x30 /* Bits 31..11 are address, 10..1 reserved */
#define PCI_ROM_ADDRESS_ENABLE 0x01
#define PCI_ROM_ADDRESS_MASK (~0x7ffUL)
#define PCI_CAPABILITY_LIST 0x34 /* Offset of first capability list entry */
/* 0x35-0x3b are reserved */
#define PCI_INTERRUPT_LINE 0x3c /* 8 bits */
#define PCI_INTERRUPT_PIN 0x3d /* 8 bits */
#define PCI_MIN_GNT 0x3e /* 8 bits */
#define PCI_MAX_LAT 0x3f /* 8 bits */
/* Header type 1 (PCI-to-PCI bridges) */
#define PCI_PRIMARY_BUS 0x18 /* Primary bus number */
#define PCI_SECONDARY_BUS 0x19 /* Secondary bus number */
#define PCI_SUBORDINATE_BUS 0x1a /* Highest bus number behind the bridge */
#define PCI_SEC_LATENCY_TIMER 0x1b /* Latency timer for secondary interface */
#define PCI_IO_BASE 0x1c /* I/O range behind the bridge */
#define PCI_IO_LIMIT 0x1d
#define PCI_IO_RANGE_TYPE_MASK 0x0f /* I/O bridging type */
#define PCI_IO_RANGE_TYPE_16 0x00
#define PCI_IO_RANGE_TYPE_32 0x01
#define PCI_IO_RANGE_MASK ~0x0f
#define PCI_SEC_STATUS 0x1e /* Secondary status register, only bit 14 used */
#define PCI_MEMORY_BASE 0x20 /* Memory range behind */
#define PCI_MEMORY_LIMIT 0x22
#define PCI_MEMORY_RANGE_TYPE_MASK 0x0f
#define PCI_MEMORY_RANGE_MASK ~0x0f
#define PCI_PREF_MEMORY_BASE 0x24 /* Prefetchable memory range behind */
#define PCI_PREF_MEMORY_LIMIT 0x26
#define PCI_PREF_RANGE_TYPE_MASK 0x0f
#define PCI_PREF_RANGE_TYPE_32 0x00
#define PCI_PREF_RANGE_TYPE_64 0x01
#define PCI_PREF_RANGE_MASK ~0x0f
#define PCI_PREF_BASE_UPPER32 0x28 /* Upper half of prefetchable memory range */
#define PCI_PREF_LIMIT_UPPER32 0x2c
#define PCI_IO_BASE_UPPER16 0x30 /* Upper half of I/O addresses */
#define PCI_IO_LIMIT_UPPER16 0x32
/* 0x34 same as for htype 0 */
/* 0x35-0x3b is reserved */
#define PCI_ROM_ADDRESS1 0x38 /* Same as PCI_ROM_ADDRESS, but for htype 1 */
/* 0x3c-0x3d are same as for htype 0 */
#define PCI_BRIDGE_CONTROL 0x3e
#define PCI_BRIDGE_CTL_PARITY 0x01 /* Enable parity detection on secondary interface */
#define PCI_BRIDGE_CTL_SERR 0x02 /* The same for SERR forwarding */
#define PCI_BRIDGE_CTL_NO_ISA 0x04 /* Disable bridging of ISA ports */
#define PCI_BRIDGE_CTL_VGA 0x08 /* Forward VGA addresses */
#define PCI_BRIDGE_CTL_MASTER_ABORT 0x20 /* Report master aborts */
#define PCI_BRIDGE_CTL_BUS_RESET 0x40 /* Secondary bus reset */
#define PCI_BRIDGE_CTL_FAST_BACK 0x80 /* Fast Back2Back enabled on secondary interface */
/* Header type 2 (CardBus bridges) */
/* 0x14-0x15 reserved */
#define PCI_CB_SEC_STATUS 0x16 /* Secondary status */
#define PCI_CB_PRIMARY_BUS 0x18 /* PCI bus number */
#define PCI_CB_CARD_BUS 0x19 /* CardBus bus number */
#define PCI_CB_SUBORDINATE_BUS 0x1a /* Subordinate bus number */
#define PCI_CB_LATENCY_TIMER 0x1b /* CardBus latency timer */
#define PCI_CB_MEMORY_BASE_0 0x1c
#define PCI_CB_MEMORY_LIMIT_0 0x20
#define PCI_CB_MEMORY_BASE_1 0x24
#define PCI_CB_MEMORY_LIMIT_1 0x28
#define PCI_CB_IO_BASE_0 0x2c
#define PCI_CB_IO_BASE_0_HI 0x2e
#define PCI_CB_IO_LIMIT_0 0x30
#define PCI_CB_IO_LIMIT_0_HI 0x32
#define PCI_CB_IO_BASE_1 0x34
#define PCI_CB_IO_BASE_1_HI 0x36
#define PCI_CB_IO_LIMIT_1 0x38
#define PCI_CB_IO_LIMIT_1_HI 0x3a
#define PCI_CB_IO_RANGE_MASK ~0x03
/* 0x3c-0x3d are same as for htype 0 */
#define PCI_CB_BRIDGE_CONTROL 0x3e
#define PCI_CB_BRIDGE_CTL_PARITY 0x01 /* Similar to standard bridge control register */
#define PCI_CB_BRIDGE_CTL_SERR 0x02
#define PCI_CB_BRIDGE_CTL_ISA 0x04
#define PCI_CB_BRIDGE_CTL_VGA 0x08
#define PCI_CB_BRIDGE_CTL_MASTER_ABORT 0x20
#define PCI_CB_BRIDGE_CTL_CB_RESET 0x40 /* CardBus reset */
#define PCI_CB_BRIDGE_CTL_16BIT_INT 0x80 /* Enable interrupt for 16-bit cards */
#define PCI_CB_BRIDGE_CTL_PREFETCH_MEM0 0x100 /* Prefetch enable for both memory regions */
#define PCI_CB_BRIDGE_CTL_PREFETCH_MEM1 0x200
#define PCI_CB_BRIDGE_CTL_POST_WRITES 0x400
#define PCI_CB_SUBSYSTEM_VENDOR_ID 0x40
#define PCI_CB_SUBSYSTEM_ID 0x42
#define PCI_CB_LEGACY_MODE_BASE 0x44 /* 16-bit PC Card legacy mode base address (ExCa) */
/* 0x48-0x7f reserved */
/* Capability lists */
#define PCI_CAP_LIST_ID 0 /* Capability ID */
#define PCI_CAP_ID_PM 0x01 /* Power Management */
#define PCI_CAP_ID_AGP 0x02 /* Accelerated Graphics Port */
#define PCI_CAP_ID_VPD 0x03 /* Vital Product Data */
#define PCI_CAP_ID_SLOTID 0x04 /* Slot Identification */
#define PCI_CAP_ID_MSI 0x05 /* Message Signalled Interrupts */
#define PCI_CAP_ID_CHSWP 0x06 /* CompactPCI HotSwap */
#define PCI_CAP_ID_PCIX 0x07 /* PCI-X */
#define PCI_CAP_LIST_NEXT 1 /* Next capability in the list */
#define PCI_CAP_FLAGS 2 /* Capability defined flags (16 bits) */
#define PCI_CAP_SIZEOF 4
/* Power Management Registers */
#define PCI_PM_CAP_VER_MASK 0x0007 /* Version (2=PM1.1) */
#define PCI_PM_CAP_PME_CLOCK 0x0008 /* Clock required for PME generation */
#define PCI_PM_CAP_DSI 0x0020 /* Device specific initialization required */
#define PCI_PM_CAP_AUX_C_MASK 0x01c0 /* Maximum aux current required in D3cold */
#define PCI_PM_CAP_D1 0x0200 /* D1 power state support */
#define PCI_PM_CAP_D2 0x0400 /* D2 power state support */
#define PCI_PM_CAP_PME_D0 0x0800 /* PME can be asserted from D0 */
#define PCI_PM_CAP_PME_D1 0x1000 /* PME can be asserted from D1 */
#define PCI_PM_CAP_PME_D2 0x2000 /* PME can be asserted from D2 */
#define PCI_PM_CAP_PME_D3_HOT 0x4000 /* PME can be asserted from D3hot */
#define PCI_PM_CAP_PME_D3_COLD 0x8000 /* PME can be asserted from D3cold */
#define PCI_PM_CTRL 4 /* PM control and status register */
#define PCI_PM_CTRL_STATE_MASK 0x0003 /* Current power state (D0 to D3) */
#define PCI_PM_CTRL_PME_ENABLE 0x0100 /* PME pin enable */
#define PCI_PM_CTRL_DATA_SEL_MASK 0x1e00 /* PM table data index */
#define PCI_PM_CTRL_DATA_SCALE_MASK 0x6000 /* PM table data scaling factor */
#define PCI_PM_CTRL_PME_STATUS 0x8000 /* PME pin status */
#define PCI_PM_PPB_EXTENSIONS 6 /* PPB support extensions */
#define PCI_PM_PPB_B2_B3 0x40 /* If bridge enters D3hot, bus enters: 0=B3, 1=B2 */
#define PCI_PM_BPCC_ENABLE 0x80 /* Secondary bus is power managed */
#define PCI_PM_DATA_REGISTER 7 /* PM table contents read here */
#define PCI_PM_SIZEOF 8
/* AGP registers */
#define PCI_AGP_VERSION 2 /* BCD version number */
#define PCI_AGP_RFU 3 /* Rest of capability flags */
#define PCI_AGP_STATUS 4 /* Status register */
#define PCI_AGP_STATUS_RQ_MASK 0xff000000 /* Maximum number of requests - 1 */
#define PCI_AGP_STATUS_ISOCH 0x10000 /* Isochronous transactions supported */
#define PCI_AGP_STATUS_ARQSZ_MASK 0xe000 /* log2(optimum async req size in bytes) - 4 */
#define PCI_AGP_STATUS_CAL_MASK 0x1c00 /* Calibration cycle timing */
#define PCI_AGP_STATUS_SBA 0x0200 /* Sideband addressing supported */
#define PCI_AGP_STATUS_ITA_COH 0x0100 /* In-aperture accesses always coherent */
#define PCI_AGP_STATUS_GART64 0x0080 /* 64-bit GART entries supported */
#define PCI_AGP_STATUS_HTRANS 0x0040 /* If 0, core logic can xlate host CPU accesses thru aperture */
#define PCI_AGP_STATUS_64BIT 0x0020 /* 64-bit addressing cycles supported */
#define PCI_AGP_STATUS_FW 0x0010 /* Fast write transfers supported */
#define PCI_AGP_STATUS_AGP3 0x0008 /* AGP3 mode supported */
#define PCI_AGP_STATUS_RATE4 0x0004 /* 4x transfer rate supported (RFU in AGP3 mode) */
#define PCI_AGP_STATUS_RATE2 0x0002 /* 2x transfer rate supported (8x in AGP3 mode) */
#define PCI_AGP_STATUS_RATE1 0x0001 /* 1x transfer rate supported (4x in AGP3 mode) */
#define PCI_AGP_COMMAND 8 /* Control register */
#define PCI_AGP_COMMAND_RQ_MASK 0xff000000 /* Master: Maximum number of requests */
#define PCI_AGP_COMMAND_ARQSZ_MASK 0xe000 /* log2(optimum async req size in bytes) - 4 */
#define PCI_AGP_COMMAND_CAL_MASK 0x1c00 /* Calibration cycle timing */
#define PCI_AGP_COMMAND_SBA 0x0200 /* Sideband addressing enabled */
#define PCI_AGP_COMMAND_AGP 0x0100 /* Allow processing of AGP transactions */
#define PCI_AGP_COMMAND_GART64 0x0080 /* 64-bit GART entries enabled */
#define PCI_AGP_COMMAND_64BIT 0x0020 /* Allow generation of 64-bit addr cycles */
#define PCI_AGP_COMMAND_FW 0x0010 /* Enable FW transfers */
#define PCI_AGP_COMMAND_RATE4 0x0004 /* Use 4x rate (RFU in AGP3 mode) */
#define PCI_AGP_COMMAND_RATE2 0x0002 /* Use 2x rate (8x in AGP3 mode) */
#define PCI_AGP_COMMAND_RATE1 0x0001 /* Use 1x rate (4x in AGP3 mode) */
#define PCI_AGP_SIZEOF 12
/* Slot Identification */
#define PCI_SID_ESR 2 /* Expansion Slot Register */
#define PCI_SID_ESR_NSLOTS 0x1f /* Number of expansion slots available */
#define PCI_SID_ESR_FIC 0x20 /* First In Chassis Flag */
#define PCI_SID_CHASSIS_NR 3 /* Chassis Number */
/* Message Signalled Interrupts registers */
#define PCI_MSI_FLAGS 2 /* Various flags */
#define PCI_MSI_FLAGS_64BIT 0x80 /* 64-bit addresses allowed */
#define PCI_MSI_FLAGS_QSIZE 0x70 /* Message queue size configured */
#define PCI_MSI_FLAGS_QMASK 0x0e /* Maximum queue size available */
#define PCI_MSI_FLAGS_ENABLE 0x01 /* MSI feature enabled */
#define PCI_MSI_RFU 3 /* Rest of capability flags */
#define PCI_MSI_ADDRESS_LO 4 /* Lower 32 bits */
#define PCI_MSI_ADDRESS_HI 8 /* Upper 32 bits (if PCI_MSI_FLAGS_64BIT set) */
#define PCI_MSI_DATA_32 8 /* 16 bits of data for 32-bit devices */
#define PCI_MSI_DATA_64 12 /* 16 bits of data for 64-bit devices */
/* PCI-X */
#define PCI_PCIX_COMMAND 2 /* Command register offset */
#define PCI_PCIX_COMMAND_DPERE 0x0001 /* Data Parity Error Recover Enable */
#define PCI_PCIX_COMMAND_ERO 0x0002 /* Enable Relaxed Ordering */
#define PCI_PCIX_COMMAND_MAX_MEM_READ_BYTE_COUNT 0x000c /* Maximum Memory Read Byte Count */
#define PCI_PCIX_COMMAND_MAX_OUTSTANDING_SPLIT_TRANS 0x0070
#define PCI_PCIX_COMMAND_RESERVED 0xf80
#define PCI_PCIX_STATUS 4 /* Status register offset */
#define PCI_PCIX_STATUS_FUNCTION 0x00000007
#define PCI_PCIX_STATUS_DEVICE 0x000000f8
#define PCI_PCIX_STATUS_BUS 0x0000ff00
#define PCI_PCIX_STATUS_64BIT 0x00010000
#define PCI_PCIX_STATUS_133MHZ 0x00020000
#define PCI_PCIX_STATUS_SC_DISCARDED 0x00040000 /* Split Completion Discarded */
#define PCI_PCIX_STATUS_UNEXPECTED_SC 0x00080000 /* Unexpected Split Completion */
#define PCI_PCIX_STATUS_DEVICE_COMPLEXITY 0x00100000 /* 0 = simple device, 1 = bridge device */
#define PCI_PCIX_STATUS_DESIGNED_MAX_MEM_READ_BYTE_COUNT 0x00600000 /* 0 = 512 bytes, 1 = 1024, 2 = 2048, 3 = 4096 */
#define PCI_PCIX_STATUS_DESIGNED_MAX_OUTSTANDING_SPLIT_TRANS 0x03800000
#define PCI_PCIX_STATUS_DESIGNED_MAX_CUMULATIVE_READ_SIZE 0x1c000000
#define PCI_PCIX_STATUS_RCVD_SC_ERR_MESS 0x20000000 /* Received Split Completion Error Message */
#define PCI_PCIX_STATUS_RESERVED 0xc0000000
#define PCI_PCIX_SIZEOF 4
/* PCI-X Bridges */
#define PCI_PCIX_BRIDGE_SEC_STATUS 2 /* Secondary bus status register offset */
#define PCI_PCIX_BRIDGE_SEC_STATUS_64BIT 0x0001
#define PCI_PCIX_BRIDGE_SEC_STATUS_133MHZ 0x0002
#define PCI_PCIX_BRIDGE_SEC_STATUS_SC_DISCARDED 0x0004 /* Split Completion Discarded on secondary bus */
#define PCI_PCIX_BRIDGE_SEC_STATUS_UNEXPECTED_SC 0x0008 /* Unexpected Split Completion on secondary bus */
#define PCI_PCIX_BRIDGE_SEC_STATUS_SC_OVERRUN 0x0010 /* Split Completion Overrun on secondary bus */
#define PCI_PCIX_BRIDGE_SEC_STATUS_SPLIT_REQUEST_DELAYED 0x0020
#define PCI_PCIX_BRIDGE_SEC_STATUS_CLOCK_FREQ 0x01c0
#define PCI_PCIX_BRIDGE_SEC_STATUS_RESERVED 0xfe00
#define PCI_PCIX_BRIDGE_STATUS 4 /* Primary bus status register offset */
#define PCI_PCIX_BRIDGE_STATUS_FUNCTION 0x00000007
#define PCI_PCIX_BRIDGE_STATUS_DEVICE 0x000000f8
#define PCI_PCIX_BRIDGE_STATUS_BUS 0x0000ff00
#define PCI_PCIX_BRIDGE_STATUS_64BIT 0x00010000
#define PCI_PCIX_BRIDGE_STATUS_133MHZ 0x00020000
#define PCI_PCIX_BRIDGE_STATUS_SC_DISCARDED 0x00040000 /* Split Completion Discarded */
#define PCI_PCIX_BRIDGE_STATUS_UNEXPECTED_SC 0x00080000 /* Unexpected Split Completion */
#define PCI_PCIX_BRIDGE_STATUS_SC_OVERRUN 0x00100000 /* Split Completion Overrun */
#define PCI_PCIX_BRIDGE_STATUS_SPLIT_REQUEST_DELAYED 0x00200000
#define PCI_PCIX_BRIDGE_STATUS_RESERVED 0xffc00000
#define PCI_PCIX_BRIDGE_UPSTREAM_SPLIT_TRANS_CTRL 8 /* Upstream Split Transaction Register offset */
#define PCI_PCIX_BRIDGE_DOWNSTREAM_SPLIT_TRANS_CTRL 12 /* Downstream Split Transaction Register offset */
#define PCI_PCIX_BRIDGE_STR_CAPACITY 0x0000ffff
#define PCI_PCIX_BRIDGE_STR_COMMITMENT_LIMIT 0xffff0000
#define PCI_PCIX_BRIDGE_SIZEOF 12
/*
* The PCI interface treats multi-function devices as independent
* devices. The slot/function address of each device is encoded
* in a single byte as follows:
*
* 7:3 = slot
* 2:0 = function
*/
#define PCI_DEVFN(slot,func) ((((slot) & 0x1f) << 3) | ((func) & 0x07))
#define PCI_SLOT(devfn) (((devfn) >> 3) & 0x1f)
#define PCI_FUNC(devfn) ((devfn) & 0x07)
/* Device classes and subclasses */
#define PCI_CLASS_NOT_DEFINED 0x0000
#define PCI_CLASS_NOT_DEFINED_VGA 0x0001
#define PCI_BASE_CLASS_STORAGE 0x01
#define PCI_CLASS_STORAGE_SCSI 0x0100
#define PCI_CLASS_STORAGE_IDE 0x0101
#define PCI_CLASS_STORAGE_FLOPPY 0x0102
#define PCI_CLASS_STORAGE_IPI 0x0103
#define PCI_CLASS_STORAGE_RAID 0x0104
#define PCI_CLASS_STORAGE_OTHER 0x0180
#define PCI_BASE_CLASS_NETWORK 0x02
#define PCI_CLASS_NETWORK_ETHERNET 0x0200
#define PCI_CLASS_NETWORK_TOKEN_RING 0x0201
#define PCI_CLASS_NETWORK_FDDI 0x0202
#define PCI_CLASS_NETWORK_ATM 0x0203
#define PCI_CLASS_NETWORK_OTHER 0x0280
#define PCI_BASE_CLASS_DISPLAY 0x03
#define PCI_CLASS_DISPLAY_VGA 0x0300
#define PCI_CLASS_DISPLAY_XGA 0x0301
#define PCI_CLASS_DISPLAY_OTHER 0x0380
#define PCI_BASE_CLASS_MULTIMEDIA 0x04
#define PCI_CLASS_MULTIMEDIA_VIDEO 0x0400
#define PCI_CLASS_MULTIMEDIA_AUDIO 0x0401
#define PCI_CLASS_MULTIMEDIA_OTHER 0x0480
#define PCI_BASE_CLASS_MEMORY 0x05
#define PCI_CLASS_MEMORY_RAM 0x0500
#define PCI_CLASS_MEMORY_FLASH 0x0501
#define PCI_CLASS_MEMORY_OTHER 0x0580
#define PCI_BASE_CLASS_BRIDGE 0x06
#define PCI_CLASS_BRIDGE_HOST 0x0600
#define PCI_CLASS_BRIDGE_ISA 0x0601
#define PCI_CLASS_BRIDGE_EISA 0x0602
#define PCI_CLASS_BRIDGE_MC 0x0603
#define PCI_CLASS_BRIDGE_PCI 0x0604
#define PCI_CLASS_BRIDGE_PCMCIA 0x0605
#define PCI_CLASS_BRIDGE_NUBUS 0x0606
#define PCI_CLASS_BRIDGE_CARDBUS 0x0607
#define PCI_CLASS_BRIDGE_OTHER 0x0680
#define PCI_BASE_CLASS_COMMUNICATION 0x07
#define PCI_CLASS_COMMUNICATION_SERIAL 0x0700
#define PCI_CLASS_COMMUNICATION_PARALLEL 0x0701
#define PCI_CLASS_COMMUNICATION_OTHER 0x0780
#define PCI_BASE_CLASS_SYSTEM 0x08
#define PCI_CLASS_SYSTEM_PIC 0x0800
#define PCI_CLASS_SYSTEM_DMA 0x0801
#define PCI_CLASS_SYSTEM_TIMER 0x0802
#define PCI_CLASS_SYSTEM_RTC 0x0803
#define PCI_CLASS_SYSTEM_OTHER 0x0880
#define PCI_BASE_CLASS_INPUT 0x09
#define PCI_CLASS_INPUT_KEYBOARD 0x0900
#define PCI_CLASS_INPUT_PEN 0x0901
#define PCI_CLASS_INPUT_MOUSE 0x0902
#define PCI_CLASS_INPUT_OTHER 0x0980
#define PCI_BASE_CLASS_DOCKING 0x0a
#define PCI_CLASS_DOCKING_GENERIC 0x0a00
#define PCI_CLASS_DOCKING_OTHER 0x0a01
#define PCI_BASE_CLASS_PROCESSOR 0x0b
#define PCI_CLASS_PROCESSOR_386 0x0b00
#define PCI_CLASS_PROCESSOR_486 0x0b01
#define PCI_CLASS_PROCESSOR_PENTIUM 0x0b02
#define PCI_CLASS_PROCESSOR_ALPHA 0x0b10
#define PCI_CLASS_PROCESSOR_POWERPC 0x0b20
#define PCI_CLASS_PROCESSOR_CO 0x0b40
#define PCI_BASE_CLASS_SERIAL 0x0c
#define PCI_CLASS_SERIAL_FIREWIRE 0x0c00
#define PCI_CLASS_SERIAL_ACCESS 0x0c01
#define PCI_CLASS_SERIAL_SSA 0x0c02
#define PCI_CLASS_SERIAL_USB 0x0c03
#define PCI_CLASS_SERIAL_FIBER 0x0c04
#define PCI_CLASS_OTHERS 0xff
/* Several ID's we need in the library */
#define PCI_VENDOR_ID_INTEL 0x8086
#define PCI_VENDOR_ID_COMPAQ 0x0e11
|